Search:

Type: Posts; User: Jim Becker; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.16 seconds; generated 58 minute(s) ago.

  1. Replies
    17
    Views
    932

    We finally just got a break from the excessive...

    We finally just got a break from the excessive humidity and that should hold through the week. There's also an upper level low that will be sitting above us for a few days, so there's hope for some...
  2. Replies
    13
    Views
    459

    Looks like it was wired with a common 3-wire...

    Looks like it was wired with a common 3-wire dryer plug to match whatever receptacle was in your previous shop. Base on your photos, it's actually correct. Here's why...

    Green is ground normally,...
  3. Replies
    20
    Views
    864

    While I prefer a wider arrangement as comes with...

    While I prefer a wider arrangement as comes with a J/P combo, I'll echo what Glenn just mentioned...pick something that's available as there really isn't anything innovative about most 8" jointers....
  4. Replies
    13
    Views
    31,200

    Sticky: Change your bookmark for the site to "that page"...

    Change your bookmark for the site to "that page" after you do the click on the logo, etc.
  5. Replies
    17
    Views
    932

    Send some here, Alan. I'd be very happy to take a...

    Send some here, Alan. I'd be very happy to take a third of that from you at the moment...it's very "crispy" walking outside right now...
  6. Replies
    1
    Views
    133

    If I'm not mistaken, the rails on the PCS out in...

    If I'm not mistaken, the rails on the PCS out in my temporary shop uses a 2x3 format. I measured it with the intention of buying some steel to make longer rails for it as they were cut down "a lot"...
  7. Replies
    6
    Views
    538

    Today was drawer day...which started out with a...

    Today was drawer day...which started out with a little "shopping" in the shed

    484347

    After cutting two pieces of leftover QSWO 12.5mm plywood to manageable size with the tracksaw and taking...
  8. Replies
    20
    Views
    2,368

    Aaron, there is an extensive plan for sound...

    Aaron, there is an extensive plan for sound abatement in the new shop building to be implemented and yes, some of that will be focused on the G700 location in addition to general sound consideration...
  9. That's interesting considering it's sold as paint...

    That's interesting considering it's sold as paint thinner and many of us also use it for cleaning because it doesn't leave a film behind like "mineral spirits". Or is the naptha sold in the big box...
  10. Replies
    12
    Views
    569

    The only two options I would entertain for this...

    The only two options I would entertain for this would be to either rewire the circuit properly for four wire 120/240v operation per code or replace the VFD with another 120v VFD.
  11. Replies
    8
    Views
    360

    Clear the existing sawmillcreek.org cookie(s),...

    Clear the existing sawmillcreek.org cookie(s), close the browser completely (and consider rebooting the machine and then start the browser followed by logging in with the box checked to remember you....
  12. Replies
    8
    Views
    831

    Yes, initial cost is high, but after a few years,...

    Yes, initial cost is high, but after a few years, things will balance out a bit more and the quality of the veggies takes the rest of the pain away!
  13. That extra mass isn't hurting you in the "runs...

    That extra mass isn't hurting you in the "runs smoother" department, for sure. 'Glad it's working out!
  14. Replies
    8
    Views
    831

    Construction lumber, in general, is coming down...

    Construction lumber, in general, is coming down in price across the board, but some of the anomalies we might see out there in the home centers and lumber yards could certainly be from what they paid...
  15. That may not be true for the portables that the...

    That may not be true for the portables that the OP is considering, at least yet. Cordless tools have very much gone that route, however.

    ----

    OP, that brings up something to consider. There are...
  16. Replies
    2
    Views
    307

    No experience, although I actually touched one...

    No experience, although I actually touched one years ago. They were a decent dedicated resaw machine back in the day.
  17. Replies
    20
    Views
    2,368

    Bryan, no, I'm not up for doing my own spray foam...

    Bryan, no, I'm not up for doing my own spray foam other than corner sealing. I'll get some more current quotes, however, once I'm closer to build. Getting response has been difficult and I may have...
  18. Replies
    40
    Views
    2,026

    Steve, I don't disagree with TWW's logic on...

    Steve, I don't disagree with TWW's logic on that...a whole bunch of cross cutting really is at 90 in my experience, so a fixed fixture, as it were, can be ideal for a lot of that work. I don't...
  19. Replies
    23
    Views
    1,091

    I've been thinking about the same thing as I...

    I've been thinking about the same thing as I visited this thread each day to see what folks have been saying. I suspect that a digital scale would be a lot more reliable than the optical sensors...
  20. Thread: MillRight?

    by Jim Becker
    Replies
    25
    Views
    1,670

    As decent and capable that Mach4 is, Acorn is...

    As decent and capable that Mach4 is, Acorn is very much next level, IMHO. It's nice that the option is there to folks to do an upgrade like that.
  21. Replies
    28
    Views
    1,721

    Yea, it's not something that might be immediately...

    Yea, it's not something that might be immediately intuitive, but scoring capability can sometimes be a "problem solver" and I'm looking forward to the new slider I bought for the new shop which...
  22. Replies
    3
    Views
    399

    "Old stock" can do that sometimes, even though...

    "Old stock" can do that sometimes, even though Zinsser products do seem to have a reasonable shelf life. 'Hope the uber-thin coating resolved things for you!
  23. Replies
    28
    Views
    1,721

    Mike, while I don't use scoring the majority of...

    Mike, while I don't use scoring the majority of the time with solid stock, I have employed it occasionally for something that it was critical for me to get a very clean cut both top and bottom. It's...
  24. That was likely a very good choice for this...

    That was likely a very good choice for this application...designed for the task for sure.
  25. Replies
    40
    Views
    2,026

    I"ve only had a cabinet saw in my (temporary...

    I"ve only had a cabinet saw in my (temporary shop) for about a year right now and I had to nearly immediately make up a crosscut sled in order to safely (at least for me) do that kind of work. A sled...
Results 1 to 25 of 489
Page 1 of 20 1 2 3 4