Search:

Type: Posts; User: Doug Garson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    14
    Views
    726

    I assume you did the obvious, ask your machinist...

    I assume you did the obvious, ask your machinist if he could do it or recommend someone?
  2. Replies
    14
    Views
    961

    I assumed from your OP that you had square holes...

    I assumed from your OP that you had square holes that you had no use for and wanted round holes to replace them. If you don't want to replace the square holes with round holes I agree both holes may...
  3. Replies
    50
    Views
    1,977

    Are you sure? Tried to get in again and couldn't.

    Are you sure? Tried to get in again and couldn't.
  4. Replies
    50
    Views
    1,977

    Wonder if they are getting a lot of traffic from...

    Wonder if they are getting a lot of traffic from people just curious about the new site and that's slowing things down? Maybe it will take a few days for the traffic to return to normal levels. Gotta...
  5. Replies
    11
    Views
    590

    I like the ones from banks I don't have accounts...

    I like the ones from banks I don't have accounts with telling me my account is on hold. My favorite, and they have called about a dozen times, is the calls in Chinese, not sure what the scam is.
  6. Replies
    14
    Views
    961

    It would seem quite straight forward rip up some...

    It would seem quite straight forward rip up some scrap wood to plug the square holes so you could then center a drill in the plug and drill a round hole. Am I missing something?
  7. Replies
    13
    Views
    452

    Sounds like you got a good deal.

    Sounds like you got a good deal.
  8. Replies
    13
    Views
    452

    Sounds a bit high, there's a Rockwell 28-200 on...

    Sounds a bit high, there's a Rockwell 28-200 on Craigslist in Vancouver BC for $350 Cnd, this is description in the ad.

    Bandsaw comes with throat extender block, new tires, three blades, and a...
  9. Replies
    37
    Views
    1,809

    How hard would it be to make a temporary ramp to...

    How hard would it be to make a temporary ramp to get over the 1 in threshold.
  10. Do you have some left over offcuts from the top?...

    Do you have some left over offcuts from the top? Could you duplicate the defect using that material and try the clear epoxy repair on it?
  11. Replies
    7
    Views
    922

    Good point, my locked miter router bit suggestion...

    Good point, my locked miter router bit suggestion may not be viable in your case.
  12. Replies
    7
    Views
    922

    How about a lock mitre router bit? ...

    How about a lock mitre router bit?

    https://www.youtube.com/watch?v=xbJszKqyfBA
  13. Replies
    98
    Views
    6,431

    Gotta agree, that is one butt ugly house inside...

    Gotta agree, that is one butt ugly house inside and out.
  14. Replies
    6
    Views
    382

    Thanks for clarifying, good tip.

    Thanks for clarifying, good tip.
  15. Replies
    98
    Views
    6,431

    That's pretty good for a low tech and probably...

    That's pretty good for a low tech and probably relatively low cost method. Sometimes simple is good.
  16. Replies
    6
    Views
    382

    Or flush cut saw.

    Or flush cut saw.
  17. Replies
    133
    Views
    13,507

    Sticky: Please register me, thanks.

    Please register me, thanks.
  18. Replies
    98
    Views
    6,431

    Anyone know what the reason is for this? This...

    Anyone know what the reason is for this? This would presumably promote small run of river type projects (assuming there are tax breaks for renewable projects) but why not promote all hydro? Apologies...
  19. Replies
    98
    Views
    6,431

    I think you are in the minority in excluding...

    I think you are in the minority in excluding hydro from renewable power sources https://sciencing.com/facts-5778942-hydropower-non-renewable-renewable-resource-.html .
    Are you suggesting Norway...
  20. Replies
    98
    Views
    6,431

    Yes simple cycle gas turbines are much faster...

    Yes simple cycle gas turbines are much faster than a coal fired power plant but not seconds, a GE aeroderivative LM 6000 gas turbine minimum start time is 5 min while a coal fired plant is more like...
  21. Replies
    98
    Views
    6,431

    Agree with some of what you say but I think you...

    Agree with some of what you say but I think you are wrong two points. One, hydro is a renewable energy source. Yes in theory a drought could reduce the ability to generate power but at least in North...
  22. Replies
    98
    Views
    6,431

    Bet the same was said about gasoline when Henry...

    Bet the same was said about gasoline when Henry Ford introduced mass production of automobiles with gasoline powered engines.
  23. Replies
    98
    Views
    6,431

    Wow, a 1948 "floor furnace" (what's that?) still...

    Wow, a 1948 "floor furnace" (what's that?) still working. I'm impressed, my oldest working thing (other than my 1949 body) is a 1954 Delta Homecraft drill press.
  24. Thread: VFD Help

    by Doug Garson
    Replies
    13
    Views
    708

    Another source of VFDs is Jack Foresberg who is a...

    Another source of VFDs is Jack Foresberg who is a member on this forum.
  25. Replies
    98
    Views
    6,431

    I'm always amazed when I hear that islands like...

    I'm always amazed when I hear that islands like the US Virgin Islands don't already generate the majority of their electricity from wind and solar. I believe they are in the process of getting their...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4