Search:

Type: Posts; User: sean meltvedt; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Richard, the knives ( like the one on the left )...

    Richard, the knives ( like the one on the left ) are removed and replaced with weights and a single molding knife (the molding knife is on the right in the pic). The molding knife can extend below...
  2. This is the same as the Belsaw moulder. The...

    This is the same as the Belsaw moulder. The pattern knife should be completely bottomed in the head. On some of the deeper patterns, I have had to take a pretty large first bite. I have also pre...
  3. John-I’m right with you. Enduro fits my shop...

    John-I’m right with you. Enduro fits my shop workflow perfectly. It’s been a great performing finish with zero comebacks due to finish failure. I’m very hesitant to use a consumer grade product off...
  4. Jerry, this was a full unopened case stored...

    Jerry, this was a full unopened case stored between 62-68 degrees. So I don’t expect it to have been a storage problem. (Other than stored for too long, over two years at my shop and more than that...
  5. 497802A little more information-evidently this...

    497802A little more information-evidently this case was 5 years old, the cans were unopened. So it was probably just bad luck. It’s a great product, too bad they don’t date their cans anymore. ...
  6. Alternates for GF ArmRseal and Enduro clear poly

    First, I am very happy with the results I receive with a wiped on base coat of armRseal, followed by sprayed Enduro clear poly topcoats. Unfortunately getting enduro during the Alaska winter is...
  7. Fairbanks Alaska here, summer indoor relative...

    Fairbanks Alaska here, summer indoor relative humidity of 70-90 %, winter indoor relative humidity 10-20 %. All my cabs are 3/4 plywood boxes (finished both sides) some doors are 3/4 solid wood...
  8. Replies
    13
    Views
    2,907

    Jon-I’d go to Harbor Freight and get their cheap...

    Jon-I’d go to Harbor Freight and get their cheap bagger, just don’t hook the bag up.
    merry Christmas
    Sean
  9. These folks also provide great long distance...

    These folks also provide great long distance service to Alaska. They are my first choice!
    cheers, Sean
  10. Scott-I too would use the original finish. If...

    Scott-I too would use the original finish. If you really want to refinish, I would match the original to hide the unavoidable panel shrink that will happen during our Fairbanks winters. Also if you...
  11. Replies
    48
    Views
    7,763

    Martin, I’ve had my PCS for over a decade now. ...

    Martin, I’ve had my PCS for over a decade now. No problems other than a fired brake or two. I recently picked up an ICS that had a roof collapse on it, the majority of the effort to get it back in...
  12. Replies
    10
    Views
    1,558

    479335479336 36” rails with the left extension...

    479335479336

    36” rails with the left extension removed gives you an approximate 48” rip capacity. This saw was damaged and the left side table was not serviceable. The rails came from my PCS...
  13. Replies
    31
    Views
    6,205

    I’m a bagger. To ensure the 42 gal Home Depot...

    I’m a bagger. To ensure the 42 gal Home Depot trash bag conforms to the inside of the 30 gal drum, I have a 240V fish tank air pump that pulls from below the bag and returns to the inlet of the...
  14. Replies
    18
    Views
    2,768

    I use Yonico solid carbide down cut and...

    I use Yonico solid carbide down cut and compression cut bits almost exclusively with great results. Depending on the number of parts, I typically get 10-12 sheets of prefinished 3/4 ply per bit...
  15. Replies
    14
    Views
    2,296

    468732 David, please forgive the post turkey...

    468732
    David, please forgive the post turkey mess, but not only are the heights different, but the depths as well. I was really hesitant to build them, but when my beautiful lady asks……. It...
  16. To answer some of the questions-the pictured...

    To answer some of the questions-the pictured plate was originally the ICS plate that was last used on the PCS so they don’t share the exact same curf. The epoxy is West 105 with either the 206 or...
  17. Maybe epoxy renew on zero clearance is a bad idea

    For a while I have been thinking it’s a great idea to use leftover epoxy to renew my zero clearance throat plates. Well I’m now reconsidering-as this blade is decided trash with 25 of 40 teeth...
  18. You’ll also likely need a new contactor-but...

    You’ll also likely need a new contactor-but unless it’s a huge monster motor I’m in the VFD camp as the best option.
  19. Replies
    40
    Views
    7,970

    Bob-looks awesome and clean. Now time to make...

    Bob-looks awesome and clean. Now time to make some dust!
    Cheers
    Sean
  20. Replies
    27
    Views
    4,388

    Scott I would certainly meet you for coffee, or...

    Scott I would certainly meet you for coffee, or at the shop. I’ve attempted to send a PM a couple of times not sure if you got them, as they don’t show in my “sent” items. Anyway let me know if you...
  21. Replies
    27
    Views
    4,388

    Scott, the guys at CCHRC at the university are...

    Scott, the guys at CCHRC at the university are very helpful. I’m also in Fairbanks and heat/cool the whole house with a GSHP. I’m using the “remote” wall system. We can meet up and I’ll show you...
  22. Yeah Brad-I’m more than slightly jealous. I’ve...

    Yeah Brad-I’m more than slightly jealous. I’ve had mine on order since February 16, but it has to ship to Alaska from their Washington location ☹️
  23. Matt it gets you a separate variable speed feed...

    Matt it gets you a separate variable speed feed motor that should also eliminate the weak drive gear that runs the feed mechanism from the cutter head of the rest of this style of 4 post planers out...
  24. Replies
    8
    Views
    1,377

    Kevin, FYI the 1033x was back ordered until mid...

    Kevin, FYI the 1033x was back ordered until mid June when I attempted to order in February. Instead I’ve got a south bend 1109 on order. Hasn’t shipped yet-I’m hopeful that it will ship soon!...
  25. Replies
    18
    Views
    2,533

    Mike-I wish. Typically the shop is clean twice a...

    Mike-I wish. Typically the shop is clean twice a year-spring and fall. Since spring hasn’t yet sprung in Alaska-her is the saw from another angle. The far table is one of those 3D looking end grain...
Results 1 to 25 of 158
Page 1 of 7 1 2 3 4