Search:

Type: Posts; User: Jim Becker; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.12 seconds.

  1. In this photo, you can see the connection for my...

    In this photo, you can see the connection for my saw...5" to the 120mm port on the saw with a wye to 3" to the blade guard branched off the 6" main. Both ports have independent blast gates. Honestly...
  2. Replies
    4
    Views
    167

    Mike, if I needed income from my part time...

    Mike, if I needed income from my part time woodworking business to live, I'd be seriously concerned right now. My best customers are small makers, themselves, and their customers are tenuous, too. So...
  3. Replies
    6
    Views
    526

    https://sgepwq.sn.files.1drv.com/y4mybTci9KE1XVU6z...

    https://sgepwq.sn.files.1drv.com/y4mybTci9KE1XVU6zXuO1TAQtTSOp0F4TQqf06k4jbzEs9CdVQV5pWN0ukS_n-wjIGBl-YG5nNhC0I6-nLl4Ea1DISKvldjmWaF78vHW35fU1z_LijAeM0LYrV2XFYex5rYhXObOakTEn1MbXbuc1LudHyfT3EinkvRNNcC...
  4. Replies
    6
    Views
    526

    This is a steal and if I actually had a use for...

    This is a steal and if I actually had a use for that format of sander, it would already be on its way to my shop...
  5. While our daughters were in their "more...

    While our daughters were in their "more impressionable" years, I moved to using OpenDNS for filtering of sites because of inconsistencies with using the router for filtering and used password...
  6. Replies
    9
    Views
    552

    Thank you, Mike. That's the replacement floor I...

    Thank you, Mike. That's the replacement floor I installed a number of years ago...largely for safety reasons, but it does look good. The floor in that room when we bought the house had been "sanded...
  7. You'd only be cutting between the two existing...

    You'd only be cutting between the two existing cuts to remove the big piece of waste and it would leave only a little to deal with via a sharp chisel. You can remove it with a bandsaw but that will...
  8. Remove waste initially with a drill and depth...

    Remove waste initially with a drill and depth stop. Make a template that you can use with a bearing guided router bit to clean the edges...it can be stuck down with the painter's tape and CA glue...
  9. Replies
    20
    Views
    556

    My experience is similar. I think that a lot of...

    My experience is similar. I think that a lot of this misrouting is because of damaged or incorrect bar codes or difficult to read zip codes on hand addressed items. This stuff is all sorted and...
  10. When I look at this photo: ...

    When I look at this photo:

    https://sawmillcreek.org/attachment.php?attachmentid=436631&d=1594491040

    I see a short cut between the two kerfs. That's why I and Derek are saying fretsaw. There's...
  11. Replies
    2
    Views
    112

    BLO by itself is completely compatible with an...

    BLO by itself is completely compatible with an oil based varnish or "poly" if it's cured. Many even use BLO as a base ingredient before they are "cooked". If it's a BLO and wax finish, however, the...
  12. He's only needing to do the short waste cut based...

    He's only needing to do the short waste cut based on the photo which shouldn't be a problem for a fret saw and would leave less to clean up than doing the angles and nibble dance with a band...
  13. Replies
    9
    Views
    552

    Thanks, David. She does appreciate the work I do...

    Thanks, David. She does appreciate the work I do for her and for the house.
    -----

    So this "flat thing" project is done. Not an exciting project, not a complicated project, not even any jointery....
  14. First thing that came to my mind was a fretsaw,...

    First thing that came to my mind was a fretsaw, too. You have the room with the kerfs to use one if my eyes are not deceiving me and can then clean them at the visible edges with very sharp chisels.
  15. Replies
    30
    Views
    1,094

    You deleted your most previous recent post prior...

    You deleted your most previous recent post prior the new one, Jon. :)

    Torsion boxes are great for assembly including clamping if they are setup well for the need.
  16. That's about the distance I'm at spraying with a...

    That's about the distance I'm at spraying with a pretty generous fan on the flat piece of mahogany in my current project thread. It's an "art form" to be consistent with this, too!
  17. Little dabs of hot melt for temporary. Hide glue...

    Little dabs of hot melt for temporary. Hide glue for "more permanent" that can still be taken apart if required.
  18. Replies
    9
    Views
    373

    The DXF file defines the project and can provide...

    The DXF file defines the project and can provide the vectors (the type of lines that are turned into CNC instructions) to the maker. But that's just the start of the journey. Those drawings need to...
  19. Replies
    30
    Views
    1,094

    "Theoretically", airflow between sheets and...

    "Theoretically", airflow between sheets and between boards for solid stock would be ideal...but it's impractical for dried material, IMHO. I do sticker dry solid stock when it first comes into my...
  20. That's really drool-worthy, Johnny!

    That's really drool-worthy, Johnny!
  21. Replies
    14
    Views
    428

    Make custom cauls so you can clamp them up or at...

    Make custom cauls so you can clamp them up or at least stabilize them while using the tape.
  22. Total Boat has some really nice products...

    Total Boat has some really nice products...
  23. Thread: Bubbles!

    by Jim Becker
    Replies
    1
    Views
    92

    That looks like a pretty heavy coat went on and...

    That looks like a pretty heavy coat went on and maybe right over the grain filler..

    You may want to consider using the EM1000 to seal and promote adhesion after your grain filler with the a...
  24. Thanks for that document reference, John. Much...

    Thanks for that document reference, John. Much appreciated!
  25. Replies
    30
    Views
    1,094

    You can build a formal structure that provides...

    You can build a formal structure that provides proper support so that the sheets can "lean" for gravity to keep them in place, but no bend because they are fully supportive. A few degrees is all that...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4