Search:

Type: Posts; User: Prashun Patel; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.51 seconds.

  1. Replies
    14
    Views
    404

    In fact, you can run them through the planer or...

    In fact, you can run them through the planer or jointer after gluing them on.
  2. Replies
    16
    Views
    374

    The problem with the 2 stage systems or semi pro...

    The problem with the 2 stage systems or semi pro systems (I have the Fuji) is that you donít get precise control over the air and flow. You have to dial things in by feel.

    Personally I like my...
  3. yes it will. MDF also wears blades faster. One...

    yes it will. MDF also wears blades faster. One has to do what one has to do, but I wouldn't subject a premium blade to it.
  4. Replies
    16
    Views
    763

    Even once the rip gets going it helps to keep the...

    Even once the rip gets going it helps to keep the wood tilted away. I try to rip on my saw bench which makes you do it this way.


    However, I was taught that if you just kiss the teeth and keep...
  5. Replies
    40
    Views
    1,432

    I donít have the discipline to make my own plans....

    I donít have the discipline to make my own plans. I have bought detailed plans for complicated builds like a rocking chair or guitar. These things have non intuitive measurements or steps.
    ...
  6. Replies
    13
    Views
    868

    sorry... waterbased

    sorry... waterbased
  7. Replies
    170
    Views
    11,618

    Phil: You should start a separate thread for...

    Phil: You should start a separate thread for this. Would like to know more details. That is just marvelous. It's exactly the type of work I respect most: great wood choice, tight joints, and...
  8. Replies
    13
    Views
    868

    I suspect the temperature is the culprit. The...

    I suspect the temperature is the culprit. The material has to atomize properly and flow out properly. A lower temperature could be making the material slightly thicker. The nozzle may also not be...
  9. Replies
    9
    Views
    1,587

    Unsolicited advice alert: Also, be advised...

    Unsolicited advice alert:

    Also, be advised that all the sculpting takes a lot of time. There's no short cutting it or productionizing it. You can get power tools and grinders large and small to...
  10. Replies
    21
    Views
    1,280

    neither am I a metalurgist, and perhaps I am...

    neither am I a metalurgist, and perhaps I am using the terms incorrectly.

    I only meant to imply that the staining is a cosmetic nuisance but doesn't corrode it to the point of compromising the...
  11. Replies
    21
    Views
    1,280

    The staining isn't corrosion; it's oxidation . ...

    The staining isn't corrosion; it's oxidation . But it doesn't look nice, I agree.

    The bigger functional problem is the actual rust caused by wet wood. That's not unique to red oak. You're lucky...
  12. Replies
    30
    Views
    1,479

    If you are having this problem with different...

    If you are having this problem with different boards I highly suspect it is your alignment and not the fault of the board.


    Check first that your riving knife is the same thickness as your blade...
  13. Replies
    10
    Views
    541

    When you get into waterbased finishes they are...

    When you get into waterbased finishes they are almost always film forming. A hand planed vs a properly sanded surface will be indistinguishable.

    The trick is to sand up to a high grit. Go to...
  14. Replies
    15
    Views
    852

    I do exactly this and am happy with it. I am...

    I do exactly this and am happy with it. I am only using it for my lathe but itís a great solution. You can make it as tall or short as you need because you have to build the rack or wall mounts.
  15. Replies
    44
    Views
    5,527

    Thank you, Olivia. You will. And it will be...

    Thank you, Olivia. You will. And it will be much sooner than you expect. Lots of great support here. Jump in!!!!!
  16. Replies
    6
    Views
    349

    I got good results with the 1.5mm tip and I did...

    I got good results with the 1.5mm tip and I did not thin at all. *if* i felt the need to thin, I'd use the retarder not water. But I didn't have to do that.
  17. Replies
    6
    Views
    349

    I just used this product on my son's bathroom...

    I just used this product on my son's bathroom vanity.

    I infact also have the Fuji Semi Pro 2. I used the stock 1.5 tip.

    I used Em6500 (tinted to a Benjamin Moore color) and HSF5000 WB...
  18. Replies
    9
    Views
    1,587

    Iíd get the Morrison plans. I have done a...

    Iíd get the Morrison plans. I have done a couple of his. The shaping and sculpting is something you just have to observe and practice. No plans will give that to you. Morrisonís DVDís are long...
  19. Bowl gouges have solid tangs. Spindle gouges not...

    Bowl gouges have solid tangs. Spindle gouges not necessarily.
    Spindle gouges generally have more acute (sharper) nose angles than bowl gouges.
    Bowl gouges often have the corners of their cutting...
  20. Replies
    41
    Views
    2,221

    I can't help but think this is an academic...

    I can't help but think this is an academic discussion. I've never had a domino joint fail. Always figured they're so small in the end - even on the DF700 that it just doesn't matter. When doing...
  21. Replies
    41
    Views
    2,221

    I know this really negates the benefit of using...

    I know this really negates the benefit of using dominos for joinery, but I donít care; it works for me.

    I make my tenons just a shade thick. made a tiny planing atop bench hook and use a block...
  22. Replies
    41
    Views
    2,221

    I buy the taytools knockoffs for the 5mm. Only...

    I buy the taytools knockoffs for the 5mm. Only because itís a pain for me to plane and shape stuff that small and I use them for cabinets where I may need so many, the time saved is worth it.
    ...
  23. Replies
    34
    Views
    1,539

    I have the Veritas jointer. It's a good plane -...

    I have the Veritas jointer. It's a good plane - but don't get it just for the auxiliary fence.

    Practice. Color an edge and take thin shavings. You'll see where your pressure is off. After a...
  24. Replies
    50
    Views
    4,486

    Does your table saw have a Riving knife? That's...

    Does your table saw have a Riving knife? That's the number one way to do it, IMHO if you don't use a guard.
  25. I would put the dust collector close to the door...

    I would put the dust collector close to the door (easier to empty) and it's pulling air and dust towards the entrance. In fact, if you can house or vent it outside, that would be my pref...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4