Search:

Type: Posts; User: glenn bradley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.13 seconds.

  1. It should eventually become brittle and pop off...

    It should eventually become brittle and pop off for the most part. If you can, clean off the areas that cause issue and wait out the rest. If you are dead set on getting it off, alcohol is your...
  2. Replies
    7
    Views
    236

    One bad review doesn't black ball a business but,...

    One bad review doesn't black ball a business but, what was the complaint? Was it something minor like late shipping and the person went on a rant or was their a valid business conduct failure being...
  3. I'll add some credence here. I also moved to...

    I'll add some credence here. I also moved to Ridgid for most of my drill motors. It's been 15 years since I bought a battery or paid for a repair.
  4. Replies
    4
    Views
    261

    I have had a G0490X since 2008. I have never had...

    I have had a G0490X since 2008. I have never had to adjust it since initial setup. Are you speaking of the table going out of plane corner to corner or simply a loss of height position? Unless the...
  5. Too true. Anvil flight cases and the like are...

    Too true. Anvil flight cases and the like are amazingly fragile when not closed up. The T&G-like aluminum extrusion that fits together does a lot of the work. More than one guy got handed his hat...
  6. Replies
    20
    Views
    549

    I am faced with this same challenge in my new...

    I am faced with this same challenge in my new shop plans. Being a woodworker (we're a clever lot but, often too clever for our own good) I came up with several versions of a bracket that would screw...
  7. Replies
    25
    Views
    972

    In that case I would go from the outside since...

    In that case I would go from the outside since the screw tip would enter a bit more material but, this could be subjective. I have scarfed long pieces together with pocket holes. They can be a...
  8. Pass on both. Go mainline or Harbor Freight. ...

    Pass on both. Go mainline or Harbor Freight. Middle ground on cordless tools leads to battery fulfillment issues IME.
  9. Replies
    6
    Views
    314

    For some, bypass can be a better 'regular'...

    For some, bypass can be a better 'regular' instead of 'test' mode :D.
  10. Replies
    8
    Views
    537

    An inaccurate measuring device serves no purpose....

    An inaccurate measuring device serves no purpose. Continuing to use one confirms the oft repeated definition of insanity. A good one doesn't cost more than the damage a junk one can cause. Do your...
  11. Nice list but, I agree that you buy as you need. ...

    Nice list but, I agree that you buy as you need. That way you auto-magically gather an array of clamps that make sense for you. I was forever running out of 24" k-body's, I would buy a few on sale...
  12. Trying to figure-match highly figured woods in a...

    Trying to figure-match highly figured woods in a lineal fashion is an exercise in frustration. Step back, take a breath and look at the combinations of figure to seek out a pleasing result. Some...
  13. Replies
    12
    Views
    396

    I'm just adding info since mine is similar. The...

    I'm just adding info since mine is similar. The Supermax hood is just a hinged metal semicircle with a 4" port similar to yours positioned dead center. It does not have any baffle plates or guides...
  14. I use a spritz of water. I have used other...

    I use a spritz of water. I have used other lubricants and all seem to work fine but, no better.
  15. Laundry never had it so good. Very nice work.

    Laundry never had it so good. Very nice work.
  16. Replies
    17
    Views
    898

    It is a pretty wood isn't it? The table came out...

    It is a pretty wood isn't it? The table came out wonderfully.
  17. Replies
    1
    Views
    256

    Back bevel on raised panel doors? What are the...

    Back bevel on raised panel doors? What are the dimensions?
  18. Replies
    13
    Views
    615

    Run your shop vac for a few minutes. Put your...

    Run your shop vac for a few minutes. Put your hand at the exhaust port. Back when we took care of houses I would use a shop vac exhaust stream to hurry along a defrosting freezer. Moving air makes...
  19. Replies
    4
    Views
    292

    Although the insert cutterhead on the Jet gets...

    Although the insert cutterhead on the Jet gets one's attention, the fact that they are still HSS and only two sided gives me visions of having to rotate cutters more frequently than I would want to. ...
  20. Replies
    10
    Views
    469

    I am generally a drawer and cabinet man. For...

    I am generally a drawer and cabinet man. For high storage I prefer open shelves or fixtures. Loose items can be contained in carefully selected storage containers, well labeled for reading from the...
  21. Replies
    12
    Views
    396

    Supermax 19-38. I assumed I would need to open...

    Supermax 19-38. I assumed I would need to open up the 4" port but, with a 2HP cyclone I have no problems. Is there something in the path that can be removed or an area where baffling can be added?
  22. Replies
    23
    Views
    1,058

    That looks like a simple case of operator "oops"....

    That looks like a simple case of operator "oops". I had a local shop grind a Woodworker II so bad they bought it from me. Shops either have to have employees with experience and skill or highly...
  23. Replies
    7
    Views
    347

    A quality motor is pretty quiet. The noise...

    A quality motor is pretty quiet. The noise should be from airflow. Even if it is both Jack's idea is great, inexpensive and easy to do. I made some window insulating baffles out of rigid foam...
  24. Replies
    17
    Views
    738

    Random info . . . . Blastgateco's tape is a...

    Random info . . . . Blastgateco's tape is a flexible vinyl coated fabric tape with a rubber adhesive similar (if not actually) 3M's 3903 and the like. Benefits are that it will mold over...
  25. Replies
    10
    Views
    506

    Nice Bill, very nice.

    Nice Bill, very nice.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4