Search:

Type: Posts; User: hugh bunker; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    1,290

    Will look into those. Thanks all.

    Will look into those. Thanks all.
  2. Replies
    6
    Views
    1,290

    Where would one order a new ruida controller? I...

    Where would one order a new ruida controller? I just googled and amazon was the only one I found and it is unavailable.
  3. Replies
    6
    Views
    1,290

    Laser upgrade questions

    I have a laser I bought in 2011 it is a re-badged redsail with a Ruida controller. The control panel buttons are working intermittently and I am having to run to the pc to start it every part. It is...
  4. Replies
    5
    Views
    1,507

    Thanks all, these should work

    Thanks all, these should work
  5. Replies
    5
    Views
    1,507

    Help with a map

    I have a friend that wants me to make a wall map in mahogany of their home country for his wife as a Christmas gift. I am having a hard time finding a good vector or even a decent enough pic to...
  6. I am currently working with a drum stick...

    I am currently working with a drum stick manufacturer and will be doing all his engraving, both logo and drummer signatures. I will see him again later today and ask if he would sell blank sticks....
  7. I have a 60 watt 600x900 and in 3 years have had...

    I have a 60 watt 600x900 and in 3 years have had to replace the tube (new tube is much more powerful than the original) and the roller wheels on the gantry wear very fast, they are available from...
  8. Replies
    23
    Views
    3,719

    Just had a similar problem with my re-badged...

    Just had a similar problem with my re-badged redsail 60 watt, turned out the ground had vibrated a little loose. It is inside the lower right hand side door. It was still snug but not tight. I...
  9. Replies
    25
    Views
    6,174

    I make them quite often for a pub up the street,...

    I make them quite often for a pub up the street, the customers take them with them. I don't seal at all as they end up being a single use item and it works out well as payment for burgers and beers.
  10. I use a Jet 10-20 drum sander wit 220 grit, it...

    I use a Jet 10-20 drum sander wit 220 grit, it only requires 2.5 inch in length and has very fine adjustment. I build 100's of 1/8 BB boxes with engravings and it cleans up both sides very well.
  11. I use the method described on the Rabbit laser...

    I use the method described on the Rabbit laser website It works fine for me, 3 years on the original mirrors and no problems.
  12. Replies
    2
    Views
    966

    Thanks Brian.

    Thanks Brian.
  13. Replies
    2
    Views
    966

    B/W globe vector

    I have a customer looking for an edge lit acrylic sign and wants their logo in it. The logo is a multicolored earth with clouds and it just wont engrave well. I can make the rest of the logo but need...
  14. Large project with some laser work involved.

    I had a friend/customer that started an ecig liquid company and will be traveling the convention circuit ask me to build a display for him. He wanted a retro industrial style with a little modern...
  15. Replies
    3
    Views
    1,247

    Thanks guys, I'll give it a go.

    Thanks guys, I'll give it a go.
  16. Replies
    3
    Views
    1,247

    Engraving for edge lighting

    I have a 18"x18" logo that I will be engraving on 1/4 cast acrylic. I have a turnkey, basically a re badged rabbit laser 60 watt and have recently replaced the tube and it seems much more powerful...
  17. Replies
    10
    Views
    4,504

    Really nice job on the surf board. I will give...

    Really nice job on the surf board. I will give them a call, looks good. Thanks
  18. Replies
    10
    Views
    4,504

    Thanks, is genuine mother of pearl cuttable with...

    Thanks, is genuine mother of pearl cuttable with the laser?
  19. Replies
    10
    Views
    4,504

    Source for mother of pearl

    I am going to be doing a set of boxes in ebony and need to inlay mother of pearl into them. It doesn't need to be real mother of pearl but needs to be thin enough to laser cut. I was thinking maybe...
  20. Replies
    86
    Views
    25,008

    I just lightly sand after. I use a festool random...

    I just lightly sand after. I use a festool random orbit sander and place the parts on a foam cabinet liner. Takes just seconds and it cleans up the engraved edges real smooth.
  21. Replies
    32
    Views
    47,350

    I have a turnkey laser that is very similar to a...

    I have a turnkey laser that is very similar to a rabbit and am right behind Charlotte motor speedway if you would like to see one run. Just let me know.
  22. Simple tabbed slip together animal puzzles

    Some friends of ours own a winery and are doing a big toys for tots drive this year. I was asked if I could donate some laser made slip together toys and want to do so. I don't have any patterns for...
  23. Thread: portraits

    by hugh bunker
    Replies
    10
    Views
    2,030

    Yes photograv saves a 1 bit B/W image for...

    Yes photograv saves a 1 bit B/W image for engraving. I find I get more detail from loading a gray scale into photograv vs a color photo. My turnkey is running laserwork 5.2 and the controller board...
  24. Thread: portraits

    by hugh bunker
    Replies
    10
    Views
    2,030

    Thanks. It's been fun trying to get the right...

    Thanks. It's been fun trying to get the right process.
  25. Thread: portraits

    by hugh bunker
    Replies
    10
    Views
    2,030

    These were 96 dpi web pics. I opened them in...

    These were 96 dpi web pics. I opened them in corel draw and changed to 8 bit greyscale bitmap then saved and opened in photograv, I resized in photograv to around 6x8 and 400 dpi then used the cherry...
Results 1 to 25 of 43
Page 1 of 2 1 2