Search:

Type: Posts; User: Phil Mueller; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. I知 not a fan of sawdust and anything mix, unless...

    I知 not a fan of sawdust and anything mix, unless it is close enough to the knot to blend in. Anything with sawdust will always be darker in color, so it might work if it痴 part of the knot.

    You...
  2. Do this.......

    Do this.......
  3. Replies
    7
    Views
    431

    Well, I知 a bit jealous. But then again, aren稚...

    Well, I知 a bit jealous. But then again, aren稚 you just going to miss resawing a large board by hand? At least I can try to justify working off the left over halloween candy bars.
  4. Sorry to hear, Kurtis. Hope all feels well soon.

    Sorry to hear, Kurtis. Hope all feels well soon.
  5. Could be technique, or could be that the set is...

    Could be technique, or could be that the set is uneven. There may be a few teeth (or more), with more set on the left than on the right. If you believe your technique is good, then I would try...
  6. That cleaned up real well. I知 with you...

    That cleaned up real well. I知 with you regarding the scotchbrite pads and light abrasive and plenty of elbow grease. Makes me cringe when heavy abrasives are used on the plate...but that痴 just me....
  7. Replies
    10
    Views
    254

    Tom, the last wood project I painted I used a...

    Tom, the last wood project I painted I used a good latex paint and thinned it with water. I used the first couple of coats to fill grain (sanding well in between), and then a few more coats to...
  8. Replies
    31
    Views
    1,197

    Looks great Jim. I知 sure you値l get a lot of...

    Looks great Jim. I知 sure you値l get a lot of use from it. Like the angle iron handles...nice touch.
  9. Congrats Curtis! If you find the time to take a...

    Congrats Curtis! If you find the time to take a few pictures, I would enjoy seeing the process you use for hammer truing and re-tensioning. Enjoy the restoration.
  10. Replies
    22
    Views
    534

    Very well done, Brian!

    Very well done, Brian!
  11. Replies
    8
    Views
    442

    Thanks all! Fred, I did eventually think of...

    Thanks all! Fred, I did eventually think of rounding the screw end...it does help to some degree. Jim, the 都hoe idea is interesting. Need to give that some thought. Rob, cool gauge. I love old...
  12. Replies
    8
    Views
    442

    Panel Gauge project

    I致e had a panel gauge in several online shopping carts for some time, but never pulled the trigger. While in the midst of waiting for finish to dry on another project, I decided to give it a go on...
  13. Replies
    28
    Views
    1,886

    Thanks for the follow along, Jim. Not sure a...

    Thanks for the follow along, Jim. Not sure a guitar build will be in my future, but appreciate seeing how it all goes together. Looking forward to seeing the finish on that wood...as I知 sure you are...
  14. I壇 guess a Disston 112 panel saw.

    I壇 guess a Disston 112 panel saw.
  15. Replies
    22
    Views
    976

    Same here as Ole. Just a bit N of Detroit and we...

    Same here as Ole. Just a bit N of Detroit and we got what looked like about 6-7 inches. Good old Toro paddle style made it through without a single clog. I never knew clogging was a...
  16. Replies
    11
    Views
    844

    This is my old made in the USA 110 bought in...

    This is my old made in the USA 110 bought in 1973. A friend has one of the Wicked Edge knife sharpening systems and honed it for me. Hasn稚 seen much use since.

    419394
  17. Replies
    1,092
    Views
    90,467

    Patrick, congrats on all the home...

    Patrick, congrats on all the home improvements...it really looks nice. I must say the garden area is spectacular...you must enjoy being in that space when you have the time to just sit and relax. ...
  18. Replies
    7
    Views
    552

    Can稚 you come up with some excuse to deadhead to...

    Can稚 you come up with some excuse to deadhead to RDU? 😉
  19. Replies
    16
    Views
    538

    Quite a number of years ago, I hung a large beam...

    Quite a number of years ago, I hung a large beam over the fireplace in our cabin. The front was floor to ceiling brick. I don’t remember the actual height that was required above the opening, but I...
  20. Replies
    22
    Views
    987

    I do tend to pre-finish as much as possible...

    I do tend to pre-finish as much as possible before glue up for all the reasons you state. I use blue tape to cover glue areas and stuff mortises with backer rod.

    A few things to consider,...
  21. Replies
    17
    Views
    1,149

    Bob, here’s a post/thread from 2012 you might...

    Bob, here’s a post/thread from 2012 you might find helpful
    https://sawmillcreek.org/showthread.php?195506-Spokeshave-chatter

    If you do a search, there may be more. Bottom line, if a quality...
  22. Replies
    8
    Views
    457

    Carl, thanks for the post, they look fantastic. ...

    Carl, thanks for the post, they look fantastic. The wood combinations are great. Truly heirloom pieces the ladies in your life will enjoy.

    Regarding the hinges: yes, worth every penny. You made...
  23. Replies
    6
    Views
    480

    Very nice! Curious, how do you manage work...

    Very nice! Curious, how do you manage work holding for those small pieces when doing final shaping/sanding/etc?
  24. Replies
    4
    Views
    375

    I’ve used it quite a bit for interior and...

    I’ve used it quite a bit for interior and exterior wood repair. I’ve only used the JB Weld product from the hardware store. It works as advertised. Just cut off the amount you need, knead it with...
  25. Replies
    56
    Views
    3,875

    IMHO anything other than some way to open the...

    IMHO anything other than some way to open the drawer from below (as suggested above) will compromise the clean look. I just don’t think you want to interrupt the cockbeading around the drawers and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4