Search:

Type: Posts; User: Derek Arita; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    18
    Views
    1,792

    Thanks Michael. Seems pretty straightforward for...

    Thanks Michael. Seems pretty straightforward for a computer dummy like me.
  2. Replies
    6
    Views
    427

    Famag Bormax Forstner Bits…

    Just got a set of these and thought I’d post here. Yes, they’re expensive, but I was at the end of my rope dealing with having to apply “tons” of pressure on my drill press to get my old bits to...
  3. Replies
    18
    Views
    1,792

    Also, I'm looking for easy to use, as I'm a real...

    Also, I'm looking for easy to use, as I'm a real dummy with this stuff.
  4. Replies
    18
    Views
    1,792

    Best Site For Posting Photos Here???

    I've been trying to use Imgur's new site, but can't make heads or tales of how to load and resize my photos for forum use. Please give me suggesting on the easiest apps to use for this?
  5. Replies
    25
    Views
    1,507

    Al, this is precisely why I added the short...

    Al, this is precisely why I added the short wooden runners to the ends of the bars. With those added bars, I can accurately cut 24”+ wide sheets and it works perfectly without being effected by...
  6. Replies
    25
    Views
    1,507

    Dan, please finish with your explanation. It...

    Dan, please finish with your explanation. It seems you were cut off. Also, I’d love to read that analysis you referred to if you can provide a link or something.
  7. Replies
    25
    Views
    1,507

    Dan, explain that to me, because it doesn’t make...

    Dan, explain that to me, because it doesn’t make intuitive sense to me. Each bar has one side in full contact with one side of its slot while the sprung side is in contact with the other side of the...
  8. Replies
    25
    Views
    1,507

    Dan, I find that hard to believe and at this...

    Dan, I find that hard to believe and at this point, couldn’t disagree with you more. I have an excellent miter gage with a long, solid fence. I can only use it for ruff cuts. Convince me.
  9. Replies
    25
    Views
    1,507

    Dan, I think you’re wrong in general, however I’m...

    Dan, I think you’re wrong in general, however I’m sure there are areas of extreme humidity swings that might apply. Having used one and two bars, I am positive that two is more dependable and gives...
  10. Replies
    25
    Views
    1,507

    Woodpecker 25.5” Miter Bars

    Just wanted to post in case anyone was interested. I was setting up to make a couple of large sleds for my SS Compact saw, so I purchased both the Woodpecker and the Incra Special Edition Miter...
  11. Replies
    11
    Views
    1,244

    What I used to do with wood bars was to put the...

    What I used to do with wood bars was to put the bars in the slots, slightly raised, apply some glue to them, then place the sled on top of them, aligned with the front of the table. That way I knew...
  12. Replies
    11
    Views
    1,244

    Ok…so I just purchased a pair of both the Incra...

    Ok…so I just purchased a pair of both the Incra and Woodpecker miter bars. The one question I have is, how do you attach the miter bar from the top? For some reason, I can’t imagine how that’s done.
  13. Replies
    11
    Views
    1,244

    Boy, that sure does seem to fit the bill,...

    Boy, that sure does seem to fit the bill, although as usual with WP, it’s pricey. Thanks.
  14. Replies
    11
    Views
    1,244

    Miter Bar Help, Please

    I’m looking for help finding good miter bars for a sled. They have to be at least 24” and screw in from the top. I’ve seen some with only 3 miter slot adjusters, however I’d like to have more. Any...
  15. Yes. For the ZCI, they’ve supplied extra inserts....

    Yes. For the ZCI, they’ve supplied extra inserts. As for the Cube, I could purchase more, print them or make some out of 4x4.
  16. Thanks, good advice. I’ll do that.

    Thanks, good advice. I’ll do that.
  17. Installed Colliflower Cube On My Kapex

    As the title says I installed the Cube along with the ZCI and I like them both. Of course, the ZCI keeps the thin off cuts from falling into the cavern of no return but the Cube gets rid of those...
  18. Hope this helps… ...

    Hope this helps…

    https://i.imgur.com/lUqPK9d.jpg
  19. Tom, I slid 2 shims on either side of the slot,...

    Tom, I slid 2 shims on either side of the slot, between contact surfaces, above the upper screw and then 2 more below the lower screw. They are short shims and must be bent to fit in those narrow...
  20. Ok Tom, you asked for it. There are two nuts...

    Ok Tom, you asked for it. There are two nuts holding on the cover of the ways. Removing those exposes where the table meets the ways and it’s where the manual says you should lubricate for smooth...
  21. Actually, it’s a 12”. My MM was a 12” as well,...

    Actually, it’s a 12”. My MM was a 12” as well, however it has Teresa knives. I find the Griz is quieter, but at a higher pitch. I’m sure the helical head helps with noise reduction. I don’t find it...
  22. Grizzly G0959 Jointer/Planer Review Lite...

    Not much posted on this machine anywhere, so I thought I'd post in case anyone is interested. The lead is, I like it, but it's not without it's issues. I've had several jointers and few planers,...
  23. Replies
    6
    Views
    625

    Ya. I know you’re right. That way I know the...

    Ya. I know you’re right. That way I know the cutter edge is even with the table, or maybe a a smidge higher?
  24. Replies
    6
    Views
    625

    Helical Head Jointer Adjustment?

    Can I rest then end of my dial indicator on the body of the head or does it have to be on the TDC of a blade edge?

    https://i.imgur.com/cBMBQ4R.jpg
  25. Replies
    4
    Views
    679

    Thanks Tom. Good info. I’m gonna give the planer...

    Thanks Tom. Good info. I’m gonna give the planer a try to save space, so we’ll see. I don’t mind shimming if needed, as it took a while get my MM J/P adjusted with shims. I’m used to change-overs....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4