Search:

Type: Posts; User: Tom Seaman; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    142
    Views
    322,813

    count me in

    count me in
  2. Replies
    182
    Views
    320,845

    count me in

    count me in
  3. Replies
    173
    Views
    322,075

    count me in

    count me in
  4. Replies
    169
    Views
    310,340

    count me in

    count me in
  5. Replies
    16
    Views
    11,865

    UPDATE: I swapped out the run capacitor and...

    UPDATE:

    I swapped out the run capacitor and still tripped the circuit. So I took the motor to a repair shop recommended by my local Woodcraft (where I bought the saw). I learned today the run...
  6. Replies
    16
    Views
    11,865

    Duane and Charles, I took the cover off the...

    Duane and Charles,
    I took the cover off the motor and checked out the centrifugal switch as you suggested. It appeared clean and dust free (it looked to be in great condition to me, but I've never...
  7. Replies
    16
    Views
    11,865

    I got a new capacitor from Jet, installed it last...

    I got a new capacitor from Jet, installed it last night, and no luck. The motor just buzzed, didn't spin, but did not trip the circuit like it did last time I tried starting it. I think my next...
  8. Replies
    16
    Views
    11,865

    Thanks guys. I got if off without any problems. ...

    Thanks guys. I got if off without any problems. There was no arc when I shorted the leads.

    Myk - I'm not 100% sure it is a bad capacitor, but that seems like a likely culprit and relatively...
  9. Replies
    16
    Views
    11,865

    Removing Capacitor from table saw motor

    My table saw motor (3 horsepower on Jet JTAS-10 cabinet saw) quit working this week, and after reading several threads here and elsewhere, I believe the problem is a bad start capacitor. After...
  10. count me in!

    count me in!
  11. COunt me in!

    COunt me in!
  12. count me in!

    count me in!
  13. Sign me up!

    Sign me up!
  14. Count me in!

    Count me in!
  15. Sign me up please!

    Sign me up please!
  16. Replies
    1,035
    Views
    121,108

    Sign me up please!

    Sign me up please!
  17. Replies
    872
    Views
    98,655

    Sign me up!

    Sign me up!
  18. Replies
    54
    Views
    11,616

    Gary, I raise the grain once and knock it back...

    Gary,
    I raise the grain once and knock it back lightly with 220 or 320 grit paper before putting on a finish (I use walnut oil on edge grain boards, salad bowl finish followed by walnut oil on end...
  19. Replies
    352
    Views
    62,195

    Count me in!

    Count me in!
  20. Replies
    4
    Views
    2,104

    Here's a review from the Rockler site, and the...

    Here's a review from the Rockler site, and the editor's note recommending a slight radius for better fit:

    Customer Rating: http://images.rockler.com/images/special/Stars40.gif
    I am building a...
  21. Replies
    17
    Views
    2,650

    I chuck a bolt with a flat head in my drill press...

    I chuck a bolt with a flat head in my drill press and use that to press pen parts together. Just use something hard (like a maple block) underneath it to keep it from digging in.
  22. Replies
    16
    Views
    4,869

    3" woodcraft casters with 3/8" stem.

    3" woodcraft casters with 3/8" stem.
  23. Replies
    16
    Views
    4,869

    I used the orange ones from Woodcraft that I...

    I used the orange ones from Woodcraft that I bought when they were 30% off at my local store (seems like they are always on discount there). They work great and were much cheaper than the Jet wheels.
  24. Replies
    583
    Views
    77,348

    nice. count me in.

    nice. count me in.
  25. count me in.

    count me in.
Results 1 to 25 of 63
Page 1 of 3 1 2 3