Search:

Type: Posts; User: Jay Kepley; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    40
    Views
    5,620

    You might consider renting a truck with a lift...

    You might consider renting a truck with a lift gate.
  2. I use a shop vac on my PCS blade guard. Works...

    I use a shop vac on my PCS blade guard. Works great. Much better than my dust collector. .
  3. Replies
    21
    Views
    1,740

    I have a Forrest WWII, and it's a very nice...

    I have a Forrest WWII, and it's a very nice blade. I recently bought three Amana blades (rip, general purpose, and crosscut), and they are very nice blades. Very clean cuts. They are a little less...
  4. Replies
    34
    Views
    6,159

    You might want to check out Mike Farrington's...

    You might want to check out Mike Farrington's video on YouTube on a large lift table. I believe that might be what you're looking for. Good luck.
  5. Replies
    34
    Views
    6,159

    450705 I have a Northern Tool lift table. I...

    450705

    I have a Northern Tool lift table. I added an mft-style top. It's really useful in many ways (some unexpected).
  6. Replies
    3
    Views
    843

    I just bought a filter set from Wynn...

    I just bought a filter set from Wynn Environmental. I'm setting up shop, and I haven't installed my old Delta air cleaner yet. I can't comment on how they work, but Wynn sells very nice stuff.
  7. Replies
    29
    Views
    2,733

    I have built several bases like this one,...

    I have built several bases like this one, including one for a Jet 6" jointer. It works great. These are HD four inch locking casters. I used some scrap SYP boards to create the wood base (sized...
  8. Replies
    6
    Views
    1,215

    I'm working on a shop light design now for my...

    I'm working on a shop light design now for my garage workshop. I reached out to American Green Lights because I had seen several YouTube folks install these lights. I was astounded at the attention...
  9. Replies
    31
    Views
    4,334

    I went with a round offset insert. It's worked...

    I went with a round offset insert. It's worked very well. The picture below is sideways. I don't know how to fix that.

    Happy New Year everyone!


    448691
  10. Replies
    41
    Views
    6,940

    Another vote for McFeely's square drive. ...

    Another vote for McFeely's square drive. Reasonably priced and work great. I keep my stock of screws in various sizes in Harbor Freight Sortimo-style bins.
  11. Replies
    39
    Views
    5,107

    447625 I use two LED lights with a magnetic base...

    447625
    I use two LED lights with a magnetic base on my bandsaw. I bought these on Amazon for about $14 each. I use them everywhere I can. The lighting is great. They are easy to move and adjust.
  12. Replies
    37
    Views
    4,591

    Mike Farrington has a commercial grade lift table...

    Mike Farrington has a commercial grade lift table that he bought used. He's got a video about an mft-style workbench/assembly table added to the lift table.
  13. Replies
    90
    Views
    20,006

    There is no question about April being a good...

    There is no question about April being a good business person. I started watching her videos from the beginning. I admire her dedication and her business model. It's worked for her. Ultimately...
  14. Thread: Track Saw?

    by Jay Kepley
    Replies
    63
    Views
    12,439

    I have a Makita corded track saw and three tracks...

    I have a Makita corded track saw and three tracks of varying lengths. This is a very useful tool, and I'm glad I have it. I have a tender back, and it is so much easier (and safer) to cut sheet...
  15. Replies
    20
    Views
    5,151

    I bought some inexpensive drawer slides from...

    I bought some inexpensive drawer slides from Custom Service Hardware. They were 14" slides. Cost about $5.00 per pair. I don't have much experience buying slides, but these were nice and work well.
  16. Replies
    37
    Views
    4,591

    I bought a Northern Tool lift table about a year...

    I bought a Northern Tool lift table about a year ago. I haven't experienced any leaking down. I did have a caster go bad, and Northern Tool replaced it. I put an MFT style top on it. It's very...
  17. I'm in the process of designing a duct system for...

    I'm in the process of designing a duct system for my 2 hp Jet dust collector (older model). I'm using five inch ducting because of the limited power of my collector. I decided to use five inch...
  18. Replies
    15
    Views
    3,019

    445537445536445538 I've made my own mobile...

    445537445536445538

    I've made my own mobile bases for my drill press and band saw. I've attached pictures. I don't know why two of them are 90 degrees off. Sorry about that.

    On the drill...
  19. I had a Jet contractor's saw for a long time. I...

    I had a Jet contractor's saw for a long time. I installed an Incra fence on it. I loved that fence. It took me more time than I'd like to admit to get it set up right, but once that was done, it...
  20. Replies
    2
    Views
    521

    I had an Incra fence on a Jet contractor table...

    I had an Incra fence on a Jet contractor table saw I sold. When the Incra fence is set up properly, it almost floats. It's an amazing tool. It took me much more time to get it set up properly than...
  21. Replies
    12
    Views
    2,232

    You might want to consider renting a truck with a...

    You might want to consider renting a truck with a lift gate and moving the saw yourself. You could just wheel it to the truck, raise it up, then wheel it in the truck. You could move any of your...
  22. Replies
    40
    Views
    9,677

    I have a Makita corded track saw and three of its...

    I have a Makita corded track saw and three of its tracks (36", 55", and the long track). I use my track saw frequently. I believe it's a great investment. It's very accurate. The Makita blade is...
  23. Replies
    64
    Views
    13,713

    It might be because the impeller on my collector...

    It might be because the impeller on my collector is only 12 inches. I don't dispute anything you've said. Dust collection and the air dynamics involved are intimidating to me. I'm going to do the...
  24. Replies
    64
    Views
    13,713

    I'm in the process of converting a 2 hp Jet dust...

    I'm in the process of converting a 2 hp Jet dust collector to a two stage. I'll offer some comments that may or may not be useful to you. First, Oneida told me that a 2 hp collector cannot support...
  25. I bought a keyless chuck from Grizzly. It was...

    I bought a keyless chuck from Grizzly. It was about $110. Fit and finish are nice. Works great. It's most likely a compromise from the upper tier chucks, but the Grizzly works great for my...
Results 1 to 25 of 94
Page 1 of 4 1 2 3 4