Search:

Type: Posts; User: Bill Webster; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Trying to avoid damage to saw blade if it hits...

    Trying to avoid damage to saw blade if it hits one.
  2. Nonferrous Pin nails or 18 Gauge Brad Nails?

    Does anyone make short non ferrous 23 gauge headless pins for a pin nailer or nails for an 18 gauge brad nailer? If so, I'm thinking it would be a good way to attach a sacrificial top to a radial...
  3. Replies
    3
    Views
    1,053

    Looks like I might have found a few J pulleys...

    Looks like I might have found a few J pulleys commonly used on lawn mowers and snow throwers.
  4. Replies
    3
    Views
    1,053

    I have looked for sheaves too with no success so...

    I have looked for sheaves too with no success so far. Automotive pulley manufacturers never say what pulley section type is, only car model. Most automotive pulleys are K section.
  5. Replies
    3
    Views
    1,053

    J Section Pulley Source?

    I have a small Vicmarc wood lathe that uses a "J" section (J3) poly-V belt. I am looking for a 4" to 6" diameter J pulley to adapt to the spindle of my larger lathe to run the Vicmarc. I thought...
  6. Replies
    15
    Views
    1,457

    You might want to have a motor shop replace the...

    You might want to have a motor shop replace the Red Star bearings. I had a 10" Multiplex that was hands-down the most difficult motor I have ever worked on. It was so bad I ended up scrapping it.
  7. Replies
    22
    Views
    1,759

    My application for a narrow blade is general...

    My application for a narrow blade is general woodworking, but more often something shop related. I have a 20" BS that I keep a 1/2" blade on and use it for most BS work. I have a 14" BS that I keep...
  8. Replies
    22
    Views
    1,759

    Jim, Not sure if you want a crown on your MM16,...

    Jim, Not sure if you want a crown on your MM16, but if you do, you can make one with progressively wider strips of Gorrilla duct tape. That is what Sulphur Grove use to recommend. On my 20" Delta,...
  9. Replies
    22
    Views
    1,759

    Jim, Did you use a V-roller for the 1/8" blade?

    Jim, Did you use a V-roller for the 1/8" blade?
  10. Replies
    22
    Views
    1,759

    Very Narrow BandSaw Blades?

    Has anyone here had experience running very narrow bandsaw blades? I was thinking about dedicating a bandsaw for use with 1/16" and 1/8" blades only. The plan was to use an upper V-roller guide only...
  11. Wall Hugger Self Cleaning Blast Gate Design

    I wanted to make a blast gate that would hug the wall within about an inch and be self cleaning. This idea has worked out very well. The gate pushes clear through to clean out the gap and the loose...
  12. Replies
    17
    Views
    1,502

    That is good advice. Wish I had more of those...

    That is good advice. Wish I had more of those empty corners though.
  13. Replies
    17
    Views
    1,502

    The Dewalt 1030 has a total carriage travel of...

    The Dewalt 1030 has a total carriage travel of 17.75" and the Omga travel is 20". Either is fine for my needs. In theory, it doesn't make sense to keep a CMS over a second good RAS if portability...
  14. Replies
    17
    Views
    1,502

    Dewalt 1030 round arm and Omga 12".

    Dewalt 1030 round arm and Omga 12".
  15. Replies
    17
    Views
    1,502

    2 RAS's and 1 CMS...Which 2 to Keep?

    I have 2 high-end RAS's (10" and 12") and a nice CMS. I only want to keep 2 of the 3 for the space I have. Which 2 would you keep and why? I don't need portability, only as stationary tools in my...
  16. Replies
    4
    Views
    8,982

    I had the same thought initially and that could...

    I had the same thought initially and that could happen in some situations. But the clamping force is not normally pulling up on the surface, rather it is pinching the surface between the dovetail...
  17. Replies
    4
    Views
    8,982

    Torsion Box for Matchfit Clamps

    I want to make a lightweight 36" x 36" x 3" torsion box with a dovetail crosshatch top for Matchfit clamps. My idea is to clamp it down to my table saw's outfeed table when in use. Has anyone made...
  18. I also wrapped the blower housing to reduce...

    I also wrapped the blower housing to reduce noise. Foam does not normally block noise, it's usually used under a barrier to absorb noise energy. But I had some very dense foam from a bed mattress...
  19. Sorry for the delay, it took me forever to find...

    Sorry for the delay, it took me forever to find those old 2012 photos of the gore point wedge. They are not very good photos, taken very close in poor light. But I think you will get the idea. The...
  20. The small block didn't help mine. The gore point...

    The small block didn't help mine. The gore point is the corner at the outlet where the air is sheared off. I added a wedge in that area.
  21. I really like my Clearvue, but it was very loud...

    I really like my Clearvue, but it was very loud when I got it. A properly designed closet is probably the most effective way to quiet it. I did several things to mine which got it down to an...
  22. Replies
    80
    Views
    332,924

    Sticky: I have purchased a lot of light fixtures for my...

    I have purchased a lot of light fixtures for my shop and I have replaced a lot of light fixtures. So here are a few opinions I have from experience.

    I will never go back to fluorescent lights. ...
  23. Replies
    2
    Views
    678

    Vince, any luck finding the manual to your...

    Vince, any luck finding the manual to your Clayton 146? I am striking out so far. It looks like the 146 is 140 look like the same sander only with different size drums.
  24. Replies
    2
    Views
    678

    Clayton 140 Sander Manual?

    Does anyone have a manual for a Clayton 140 oscillating spindle sander or know where I can get a copy. I bought an old Clayton 140 that has not been used for a while and am wondering mainly about the...
  25. I know of a 220/440 step up transformer for sale...

    I know of a 220/440 step up transformer for sale cheap, but it is 12KVA and I only need 2KVA, maybe 3KVA at the most. Would it still work ok or would there be huge losses or other problems?
Results 1 to 25 of 61
Page 1 of 3 1 2 3