Search:

Type: Posts; User: Cameron Handyside; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Art, I'm glad you got to visit with him. He...

    Art,

    I'm glad you got to visit with him. He milled a bunch of cedar for me and did a great job. I'm hoping to get a chance to build something w/ one of his thick slabs sometime in the near...
  2. Hello Jon, I'm in Huntsville too and besides...

    Hello Jon,

    I'm in Huntsville too and besides Hobby Hard Woods (who is great), there are a few other places around the area where we buy lumber:

    Bill Hughes Sawmill. He cuts custom as well as...
  3. Replies
    7
    Views
    1,495

    There are some great shops, including woodworking...

    There are some great shops, including woodworking in Fairhope, AL. Fairhope is on the Eastern Shore (Mobile on the Western Shore). There is also a wooden boat builder still in business in Mobile. ...
  4. Replies
    44
    Views
    14,812

    I used Tom's book to get me started building...

    I used Tom's book to get me started building cabinets in my shop. I started with a simple free-standing cabinet:

    319107

    After struggling with the drawer slides and faces, I built up enough...
  5. Replies
    20
    Views
    6,125

    I just installed my V-3000 in my 24x24 shop, I...

    I just installed my V-3000 in my 24x24 shop, I rant 6" Sewer & Drain pipe to all my tools and used the ClearVue Blast Gates and 6" to 2-4" fittings. Everything works really well. I did not install...
  6. I've built a number of Adirondack Chairs out of a...

    I've built a number of Adirondack Chairs out of a variety of wood. I teach a class building them at our local woodshop on a military base as well. We use Eastern Red Cedar because it is plentiful...
  7. Even though I said I was done w/ dust collection...

    Even though I said I was done w/ dust collection for awhile, I was sorting through all the leftover pieces and realized I had enough to install a floor sweep. Other than the plastic OTS floor...
  8. Don, I am sold on the V-3000. I've been running...

    Don, I am sold on the V-3000. I've been running it for a few days now and have no complaints at all. I maintained 6" pipe for as far as I coudl before switching over to 4". I have branches so if...
  9. Thanks for all the comments. Jebediah, first...

    Thanks for all the comments.

    Jebediah, first that Label Maker was a gift to my wife (who has her PhD in Mech Engineering) and it was a great investment! I did consider venting outside but I...
  10. Ole, I have not seriously leak tested the joints...

    Ole, I have not seriously leak tested the joints yet. While running, I've been moving my hand over joints, feeling for drafts and have not found any yet. I bought all the pipe and fittings from the...
  11. 308783 308784 Because I raised the cyclone, I...

    308783 308784

    Because I raised the cyclone, I had to build a platform on which the barrel could sit. I like this solution because now I have some much treasured storage space under the barrel and...
  12. Once I was comfortable with the tool connections,...

    Once I was comfortable with the tool connections, I wanted to shore up the vertical pipes. They were in no danger of falling but I was worried what might happen if I hit the pipe with a tool or...
  13. Actually hooking up all the machines is still a...

    Actually hooking up all the machines is still a work in progress. But here is what I have to-date:

    308771 308772 308773 308774

    I managed to keep 6" pipe all the way to my Grizzly Jointer. To...
  14. Getting the duct down to the tools was leading to...

    Getting the duct down to the tools was leading to consternation and I hadn't even started thinking about all the adapters, reducers and flex pipe needed to make the final connections. My goal was to...
  15. Next is running duct to all my existing machines...

    Next is running duct to all my existing machines while also preparing for a few new ones (hope springs eternal). My first step was to figure out how to cleanly cut the PVC pipe. I tried my sawsall...
  16. Oneida V-3000 Installation and Initial run

    The following is a series of pictures of my Oneida V-3000 (resin body) installation. My shop is a 24x24 free standing shop. with a seperate "bump out" I call the mechanical room where the...
  17. I'm using the zip tie anchors and 24" ties. ...

    I'm using the zip tie anchors and 24" ties. According to the literature, the tie is rated at 175lbs (I assume tension). I also invested in the tensioning/clipping tool rated for this size. I'm...
  18. Replies
    6
    Views
    2,053

    Matt, when building my shop, I had to use a...

    Matt, when building my shop, I had to use a matching garage door due to HOA rules, but we turned it into a giant pocket door, using barn door hardware. I have been very happy with it. Doesn't cover...
  19. Replies
    7
    Views
    1,550

    I believe Anna was my sales rep as well back in...

    I believe Anna was my sales rep as well back in Oct. I'll be following your install closely.

    I have my V-3000 on the wall and running as well as a pile of 6" PVC. I just found a Fernco reducer...
  20. When I ordered my v-3000 in October, I got the...

    When I ordered my v-3000 in October, I got the remote control thrown in for free. It was not listed on their website but I called and talked directly with a salesperson, who gave it to me during the...
  21. David, it's 24'x24' with a 6'x12' bump out room I...

    David, it's 24'x24' with a 6'x12' bump out room I call the "mechanical room" where I have the compressor and DC. Most of the stationary tools are on the shared wall with the bump out so I hope to...
  22. They switched from metal to resin as I was...

    They switched from metal to resin as I was working through my order with them (hence the origial post). The price did not go up during that time (I worked with them for about 2 weeks) and they...
  23. Dan, I think you are right. I may have to just...

    Dan, I think you are right. I may have to just purchase the reducer from Oneida. I'll try to post some pictures of the installation once I make some progress.

    Jack, the filter documentation...
  24. Dan, Off my shop, I have an attached room (bump...

    Dan,
    Off my shop, I have an attached room (bump out) that measures 6' x 12'. Inside it's only about 5' x 11'. The intake on the V3000 points right at the wall where it'll penetrate into my shop. ...
  25. I live in HSV as well. I used to go out to the...

    I live in HSV as well. I used to go out to the Hardwood Center in Scotsboro too, he had some really exotic wood (big boards too!). There are a few sawyers around our area, used to be H&K near...
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4