Search:

Type: Posts; User: Richard Coers; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. I plugged mine into an ancient lap top.

    I plugged mine into an ancient lap top.
  2. Giant step from $35 to $100

    Giant step from $35 to $100
  3. You are getting good cuts that makes a good joint...

    You are getting good cuts that makes a good joint between two boards? Beds are coplanar? You might try putting a block of wood on the aluminum part and tap with a hammer to see if it moves. If not, I...
  4. Replies
    9
    Views
    894

    Not at all uncommon. I was assaulted riding as...

    Not at all uncommon. I was assaulted riding as well. 4 teens on 2 dirt motorcycles sped by me on a trail. The rider of the first bike slapped me in the back, the second pair slapped me in back of the...
  5. Very rare indeed as walnut is always scrutinized...

    Very rare indeed as walnut is always scrutinized for the possibility of selling to the veneer market. That is really the place where all rare really high figured wood should go.
  6. A lot of people put too much pressure down on the...

    A lot of people put too much pressure down on the sander and that prematurely causes velcro wear. The heat generated doesn't help. 5 years is really good for tiny little hooks to work. Buy a new pad...
  7. Replies
    12
    Views
    550

    Certainly not irrelevant to everyone. A domino...

    Certainly not irrelevant to everyone. A domino machine is not for production, so quantity makes a difference.
  8. The part you are forgetting in the equation is...

    The part you are forgetting in the equation is the tensile strength of the material. Grey iron tensile strength is quite low. In metric, the ultimate tensile strength of cast iron is 1.3-1.6 tonnes...
  9. Replies
    20
    Views
    869

    I'm a big fan on old iron for a thickness planer....

    I'm a big fan on old iron for a thickness planer. Back in the day I bought a 24" Yates American machine. You could take 1/4" cuts on 12" wide boards with no hesitation. New machines are not in the...
  10. You didn't mention you were a mechanical...

    You didn't mention you were a mechanical engineer. One thread will not hold 90% of the load. It's very easy to pull out one thread in grey iron. I learned that working on farm machinery, not college.
  11. Replies
    10
    Views
    546

    Different extension gives you a different side...

    Different extension gives you a different side profile. I just mounted a block on my grinder base 2" from the front of the base. Who needs to buy gauge blocks?
  12. Remove the other 3 bolts and take the table off...

    Remove the other 3 bolts and take the table off the base. Now you can do it right. 4 threads will not hold the proper tightening torque.
  13. Yes to your question James. A replacement for the...

    Yes to your question James. A replacement for the laser pointer design.
  14. The ideal thing would have been to find and reuse...

    The ideal thing would have been to find and reuse the chip. If I was to repair it, I would take a piece of scrap wood to make a tiny bit of veneer, clean up the edges of the chipped veneer, and glue...
  15. I question the decision to make a table saw a...

    I question the decision to make a table saw a bench. You sure don't want to use a mallet driving down on a wing of the saw, It's a precision machine! I suggest who make a full bench that can roll...
  16. Replies
    21
    Views
    1,146

    And if it's getting on your glasses, it's going...

    And if it's getting on your glasses, it's going in your nose. Once in your lungs, the super fines pass through to your blood and end up in your kidneys and liver. That's the serious damage!
  17. Replies
    21
    Views
    1,146

    There are a couple good dust collector for hand...

    There are a couple good dust collector for hand held routing....
  18. Replies
    9
    Views
    574

    Does big honking mean deep too? A deep pour resin...

    Does big honking mean deep too? A deep pour resin would have been a better choice. Either move the slab out in direct sunlight, or put a heat lamp over it. I only use Alumilite dye or used coffee...
  19. I built mine a long time ago, but this camera is...

    I built mine a long time ago, but this camera is very similar. The one I bought fit right into the Jamieson laser holder. $11 ...
  20. Replies
    10
    Views
    669

    The PC 690 is not the tool it used to be. Most...

    The PC 690 is not the tool it used to be. Most use Bosch now.
  21. Replies
    64
    Views
    3,337

    There is never a "best", just one that has the...

    There is never a "best", just one that has the features someone likes. Your listing of 3 proves the point.
  22. Replies
    53
    Views
    2,128

    My curiosity is growing, is the bit out?

    My curiosity is growing, is the bit out?
  23. Replies
    14
    Views
    982

    I hope you have a card to clean up those files....

    I hope you have a card to clean up those files. Hot melt is gooey stuff.
  24. Replies
    14
    Views
    982

    Paul describes it perfectly. The trimmer tools...

    Paul describes it perfectly. The trimmer tools are just fine for plastic edge banding, horrible on wood. I also follow up the iron with a wood block to press the hot glue joint and let it cool.
  25. https://www.mcmaster.com/products/sprockets/

    https://www.mcmaster.com/products/sprockets/
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4