Search:

Type: Posts; User: Shawn Morris; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    389

    I have a switch for the laser power supply. It...

    I have a switch for the laser power supply. It appears that they just messed with the power and e-stop switches due to them overloading with the use of the rear ac outlet for powering the large...
  2. Replies
    8
    Views
    389

    It’s all good for now. Sooner or later I’ll...

    It’s all good for now. Sooner or later I’ll trace the wires from the standby switch to see where they go, just to satisfy my curiosity. All wiring and functionality otherwise is like it was...
  3. Replies
    8
    Views
    389

    Thanks for the replies. The controller wiring...

    Thanks for the replies. The controller wiring was fine. I was able to replace both the e-stop and power switch with the correct ones. Everything works, but there is one switch on the front of the...
  4. Replies
    8
    Views
    389

    X700 clone wiring help

    I just picked up a very used X700 clone that I am trying to get back into proper condition. The power switch was replaced with a light switch, and the e-stop switch was missing and bypassed. I have...
  5. Replies
    8
    Views
    1,238

    I did have success by changing the Y max acc and...

    I did have success by changing the Y max acc and keying acc settings (vendor settings). The strange thing is that when I changed the settings back to the original values, the acceleration was not as...
  6. Replies
    8
    Views
    1,238

    Due to work, I won't get back to this until...

    Due to work, I won't get back to this until Monday. I will post my results.
  7. Replies
    8
    Views
    1,238

    I did some playing around tonight and I think I...

    I did some playing around tonight and I think I am making progress. I changed the acceleration for the Y axis. It looks like the slippage has stopped but I need to get some more test material...
  8. Replies
    8
    Views
    1,238

    Slippage on shenhui 350 rotary tool

    I have been experimenting with the rotary tool but am having some issues with slippage -- just at the start and stop of the job when the rollers move very fast. This causes my images to engrave fine...
  9. Replies
    20
    Views
    3,154

    I searched craigslist until I found a small...

    I searched craigslist until I found a small aquarium chiller for under $100. I use a 5 gallon Igloo cooler to circulate the water through the chiller with one pump. I have a second pump for the...
  10. I keep mine at 18c. I would keep it colder if...

    I keep mine at 18c. I would keep it colder if not for condensation. I'm using an aquarium chiller and an Igloo 5 gallon drink cooler.
  11. Replies
    17
    Views
    5,325

    I believe yours is quite a bit newer than mine. ...

    I believe yours is quite a bit newer than mine. I also have the other controller RDLC320A in mine. I'm in Lake Mary.
  12. Replies
    17
    Views
    5,325

    Here's my power supply, yours may be different. ...

    Here's my power supply, yours may be different. Where in Florida are you?
  13. Replies
    17
    Views
    5,325

    If it did arc, you may need to hit the reset...

    If it did arc, you may need to hit the reset button on your power supply. The one on my SH-350 tripped once when i had arcing due to insulating material that had come loose.
  14. Replies
    12
    Views
    2,551

    I also have a shenhui 350 laser. Mine started...

    I also have a shenhui 350 laser. Mine started doing the same thing. I believe that there may be a common issue with these, as I purchased mine used and replaced the mainboard for this very issue. ...
  15. Replies
    59
    Views
    18,727

    Just ordered a DVD via Paypal. Thanks

    Just ordered a DVD via Paypal.

    Thanks
  16. Replies
    8
    Views
    1,115

    I'll definately give that a try. Thanks

    I'll definately give that a try. Thanks
  17. Replies
    8
    Views
    1,115

    True, but I find the manual is either vague in...

    True, but I find the manual is either vague in many areas, or maybe it's my comprehension. I know that the translation from Chinese to English doesn't help that either. Reading is about all I can...
  18. Replies
    8
    Views
    1,115

    Ken and Rich: thanks, that is along the lines of...

    Ken and Rich: thanks, that is along the lines of what I was thinking. Unfortunately my machine hasn't made it home yet and is still at a friend's house 120 miles away. Is setting these parameters...
  19. Replies
    8
    Views
    1,115

    Can engrave but not pulse the laser

    I am new to this hobby and purchased a used Sh-g350 laser enngraver. The mirrors need alignment but the laser button on the control panel does not fire the laser. I get the beep when the button is...
Results 1 to 19 of 19