And spent $1...for..
518619
From American Woodworker Magazine..
518620
Rather a thick book...
Still looking through it, too...
The "Season" has started...
Type: Posts; User: steven c newman; Keyword(s):
And spent $1...for..
518619
From American Woodworker Magazine..
518620
Rather a thick book...
Still looking through it, too...
The "Season" has started...
Might have another Nickel Plate Project for you to try...
518618
Union No. 41 match plane...
Sorry..Dry Shop...I save the booze for when I am done for the day....sometimes a Guinness,,sometimes the Tonic & Gin.....now and then maybe a shot of good Irish Whiskey?
Lid needs a rebate, like this older case has..
518597
Which gives the hinges a bit more room, and the rebate acts as a stop when the lid is opened..so..
518598
Ends were a bit deeper than the...
Total cost was just over $109, counting tax, and a 10% Discount...the items?
518594
The iron is a Stanley 2-3/8" wide, almost unused..$12?
As for the Union....No. 41....was listed as $100...got...
Ok...those clamps came off this morning...back was cleaned up..
518514
Followed by both ends, and then the front..
518515
And the top edges leveled...then the bottom was leveled...
518516
As...
Half blind dovetails for the front of the drawer...meant I needed to cut existing pins back about 1/8" from where the others were...instead of 1/2" long pins...they needed to be 3/8" long..
I...
I run about half and half...between the smooth soled and the "Groovy" soles....have yet to see any difference between the 2...
This case can then sit on a shelf..until a Project comes along that needs chisels...then it can sit down on the end of the bench, where I can access the sizes I need that day...when not in use, back...
Keyboard issues this morning...had to go and replace it. Seems a cat had walked across the computer desk, and knocked over my glass of Tonic & Gin...right onto the keyboard.
Monday....gotta love...
Got the lid to size
518454
4 parts for a Drawer..
518455
Milled a place for the drawer to house a plywood...
518457
Dovetails as well..
518458
Both ends were done first, going across the grain...a "stop line" was marked along the center of the edge, and about a 1/4" or so down the face...Tools?
518379
Spokeshave where the grain...
Clamps came off this morning...wanted to get the outside of the case cleaned up..so
518374
Ends were cleaned up..gaps filled as needed..then the front part was also cleaned up...then
518375
The...
And they call ME a Bandit? Hmm, may need to expand MY hunting grounds, I guess..
New brushes, as we will be doing a glue up, this morning..
518329
Needed a couple cauls..
518330
The other end was fine as is..checked each end for square-ness..
518331
And the other end.....
Well, a couple of them were on the job..without any issues..
518302
Such as the 1/4" sized one.
Tip: I use a dog hole or 3 to hold chisels..
518303
Keeps them from rolling off the bench, and...
Front: First try was tails first, even did the layouts..
518306
But, there were issues with that bottom corner...went back to Pins first,
518307
Because I needed to cover that groove......
11-1/2" long, 5" tall..and 5" front to back...hoping for 6 larger chisels and 6 smaller chisels..between the upper Compartment and the lower drawer...depends on how big the handles are..
Really...oh well...
Note: For those that want to try the tablesaw as a Kerfing Tool...make sure the kerf it leaves matches the kerf the rip saw will make....otherwise, you will need a plane...
518278
Just a heads up...
Ok...
518271
Lay out is done Pins first...have to work around that groove...a bit of saw work..
518272
Then a bit of chopping, show side first..
518273
Then flip over, and finish the chops..(...
Had to make a run to Harbor Freight just now....as I use their Acid Brushes to spread glue around, when gluing up Dovetails or other such joinery.
This post is a Build Thread...on how the case was...
Actually, those chisels are helping to build that case...and working quite well, too..YMMV, of course..
518248
One of the 3 planks...
518249
Another was made into 2 ends, and the back of the...
Have seen a few planes come through the Rehab Shop..that looked like the old Owner was using the chipbreaker as the cutter....on TOP of the bevel, BTW..
At least one that looks better than this?
518241
I think I can build something a little bit better than that plastic blister pack...
Maybe take a plan from Paul Sellers Masterclasses, and build...