Search:

Type: Posts; User: Scott Loven; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Please count me in!

    Please count me in!
  2. Replies
    872
    Views
    98,847

    Please count me in!

    Please count me in!
  3. Please count me in!

    Please count me in!
  4. Please count me in!

    Please count me in!
  5. Please count me in!

    Please count me in!
  6. Please count me in!

    Please count me in!
  7. Please count me in!

    Please count me in!
  8. Please count me in!

    Please count me in!
  9. Replies
    1,035
    Views
    121,359

    Please count me in!

    Please count me in!
  10. count me in!

    count me in!
  11. Replies
    31
    Views
    11,215

    I would look at it this way, what would it cost...

    I would look at it this way, what would it cost her to buy new and replace? If it can still be purchased to match the existing, suggest that she do it and that you do the install for $100. To...
  12. I find it hard to balance the lap-top on my knees...

    I find it hard to balance the lap-top on my knees in the reading room so still prefer to buy hard copy magazines!
    Scott
  13. I like the Milescraft feather boards as well as...

    I like the Milescraft feather boards as well as the bench dog line.
    Scott
  14. How about cutting a deep saw kerf underneath...

    How about cutting a deep saw kerf underneath about 2 inches back from the front and glue a piece of steel in the slot. Should make it much stiffer and almost invisible. I also would do a dado on...
  15. Replies
    268
    Views
    56,374

    count me in!

    count me in!
  16. I was just thinking about some sort of insulated...

    I was just thinking about some sort of insulated blanket that could be put up for the winter and taken down when warm, or if you needed to use the big door. I have a 10*10 steel insulated door with...
  17. Replies
    21
    Views
    7,445

    There was a Fine Woodworking Joint test a while...

    There was a Fine Woodworking Joint test a while back that was very favorable to Pocket hole Joinery. If I recall correctly it really gets down to penetration from one piece of wood into another. ...
  18. Replies
    67
    Views
    11,829

    "PS -- Personally, I think it's ridiculous to...

    "PS -- Personally, I think it's ridiculous to keep chickens when eggs are a buck a dozen. But it makes her happy, and I've got to come up with a strategy. "

    Ya, its like those people who spend...
  19. Replies
    4
    Views
    1,187

    Don't forget about the new router table lift! ...

    Don't forget about the new router table lift!

    http://www.kregtool.com/products/prs/product.php?PRODUCT_ID=118

    It seems like it would be worth it if you do cabinets for a living. Time is...
  20. Replies
    13
    Views
    1,484

    How about putting a reminder on the crank to...

    How about putting a reminder on the crank to remove the insert before you tilt the blade? A piece of plastic pipe perhaps?
    Scott
  21. Replies
    3
    Views
    3,859

    Kreg is also coming out with a new smaller drill...

    Kreg is also coming out with a new smaller drill bit and jig head and smaller screws for 1/2 inch material. The jig head will fit the K3 jig body.
    Scott
  22. Replies
    29
    Views
    3,302

    I have a Dewalt RAS with a break that doesn't...

    I have a Dewalt RAS with a break that doesn't work. I was thinking I could add a disk brake from a bicycle if it bothered me. I could not find replacement parts anywhere.
    Scott
  23. Spend the two hours and make the drive to Grizzly...

    Spend the two hours and make the drive to Grizzly after you have looked at the HF unit.
    Scott
  24. Thread: Mcfeelys

    by Scott Loven
    Replies
    6
    Views
    1,404

    Mcfeelys

    I see that they are headquartered in Madison Wisconsin now, do they have a retail store there? When did this happen?
    http://www.mcfeelys.com/

    Scott
  25. Replies
    7
    Views
    1,440

    I suggested to Kreg tool that they make an angled...

    I suggested to Kreg tool that they make an angled plug hole cutter. If you had one you could cut a plug with the proper grain orientation out of scrap wood from your project. Should be much less...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4