Search:

Hmmmm..can't edit this any more...so...it is what it is...don't feel like doing a repeat of this entry...and take a chance on the same stuff happening again...use your imagination, I guess..

There may be a second plane coming along...Stanley No. 39 3/8"
518756


We'll see...

See how this goes...
518755

A coat of Witch's Brew was mixed first....old stuff was a bit too red...dumped what was left of the Special Walnut into the can..and gave it a good stir..
Coat has been brushed on..and I am allowing...

Laundry Detail. this morning...so..despite it being a Monday....the feet have been leveled...need to unload the washer after a bit...and the Chisel Case...and see about a finish of some sort..
...

Shoptime today? feet installed....fancy feet, at that..
518732
With glue and very small nails..
518733
Letting this sit overnight...

Stay tuned..

This is getting very OLD! To correct this? Either the Mods FIX the site...or...I have to go back and re-load EACH of those photos...seems to happen about once a month..there is NOTHING changed...

Layout work...the barrel of the hinge, sits in the rebate under the lid..
518680
I set the hinge at the corner of the rebate, make a mark on the other end of the hinge,,,the lay out the hinge...

Was working on feet for the case to sit on...Miter saw cuts..
518672
Were having an issue...when a part is 1/4" x 1/4" square...and the back corner that meets the fence on a folding Mitrebox......

Hmmm..lookee what I found at a yard sale, yesterday, then.
518634
Spent a dollar bill on it..
518635
From American Woodworker magazine...

A closer look at that tag on the Stanley iron..
518630
That be the original price tag...price was $1.53....Iron has never been used, nor sharpened..still has the "Factory Grind Edge"

Logo on the...

And spent $1...for..
518619
From American Woodworker Magazine..
518620
Rather a thick book...

Still looking through it, too...

The "Season" has started...

Might have another Nickel Plate Project for you to try...
518618
Union No. 41 match plane...

Sorry..Dry Shop...I save the booze for when I am done for the day....sometimes a Guinness,,sometimes the Tonic & Gin.....now and then maybe a shot of good Irish Whiskey?

Lid needs a rebate, like this older case has..
518597
Which gives the hinges a bit more room, and the rebate acts as a stop when the lid is opened..so..
518598
Ends were a bit deeper than the...

Total cost was just over $109, counting tax, and a 10% Discount...the items?
518594
The iron is a Stanley 2-3/8" wide, almost unused..$12?

As for the Union....No. 41....was listed as $100...got...

Ok...those clamps came off this morning...back was cleaned up..
518514
Followed by both ends, and then the front..
518515
And the top edges leveled...then the bottom was leveled...
518516
As...

Half blind dovetails for the front of the drawer...meant I needed to cut existing pins back about 1/8" from where the others were...instead of 1/2" long pins...they needed to be 3/8" long..

I...

I run about half and half...between the smooth soled and the "Groovy" soles....have yet to see any difference between the 2...

This case can then sit on a shelf..until a Project comes along that needs chisels...then it can sit down on the end of the bench, where I can access the sizes I need that day...when not in use, back...

Keyboard issues this morning...had to go and replace it. Seems a cat had walked across the computer desk, and knocked over my glass of Tonic & Gin...right onto the keyboard.
Monday....gotta love...

Got the lid to size
518454

4 parts for a Drawer..
518455
Milled a place for the drawer to house a plywood...
518457
Dovetails as well..
518458

Both ends were done first, going across the grain...a "stop line" was marked along the center of the edge, and about a 1/4" or so down the face...Tools?
518379
Spokeshave where the grain...

Clamps came off this morning...wanted to get the outside of the case cleaned up..so
518374
Ends were cleaned up..gaps filled as needed..then the front part was also cleaned up...then
518375
The...

And they call ME a Bandit? Hmm, may need to expand MY hunting grounds, I guess..