Stylecnc stg 6090. That is what I really want. Input gladly welcomed
Type: Posts; User: Karl Card; Keyword(s):
Stylecnc stg 6090. That is what I really want. Input gladly welcomed
Being that I have to have financing options the long mill is out...... xcarve and shapeoko offer financing. I like the shapeoko over the xcarve. Should be ordering the shapeoko xxl next month. ...
The thing that bothers me about xcarve is that i am told I can use different software.... that is fine, the side rails are not as rigid as id like but they can be reinforced. The reviews I have read...
Hi folks, I am in the process of looking for an entry level cnc. Understand that I do not have 8K to sink into a cnc.
I am looking at the xcarve, dwc1824, and onefinity and also shapeoko.
...
I dip my pens in deft laquer. I do this 3 times. Then very lightly sand with 600 grit then put a dab of eee wax on it and i have a glass clear finish that makes the wood look like 3d. Deft is...
I want a protective coating on this because they have young grand children that visits very frequently.
I have used the cedar oil and find it disgusting. I am thinking of taking them a few bags of the cedar shavings and use that. I can always make more shaving if they need it.
I am seriously thinking of using a clear epoxy finish. I have never used epoxy and this isnt a paid job but a Christmas gift and I feel I need this to have a finish on it since these people smoke...
I am making a tv stand out of cedar for a friend. They chose cedar for looks and the "smell". So I am wondering how many problems will I create if I only finished the sides and tops of the shelves....
I have the 16/32 performax and the only p0roblem I have had is keeping the drum straight. I have bought an upgrade bracket that I still have not installed yet that is support to keep the drum in...
I ended up getting a Baldor single phase 7.5 hp motor. Needless to say it does not stall.... Got the baldor freshly redone for $300. Very heavy motor...
I thank you all very much. Very good info.
I am starting a project and will be using Odies Oil as a finish. I saw a piece where a guy sanded to 1200 but not sure if it was 1200 or P1200 but then used odies oil and I mean to tell you it was...
Hi all,
I am looking for a descent set of 5 inch sanding disk that will cover grit from 120 to about 1200. Does anyone know of a company that sells a set that covers this or am I going to have...
I would be very interested. 99 percent of my pen blanks are imported exotic woods.
Lee makes sense but at the same time I do actually enjoy using my machinery to make rough wood nice. Plus I am sitting on about 1700 board feet of kiln dried cherry, sassafras, hickory, maple,...
Thank you very much. My thoughts were pretty close but not quite same order. But I see the reasoning and that is what I was after.
Thanks. I just need to start.
I have mainly only done wood turning. Pen sets, bowls, etc. I am wanting to start into flat work but would like information
on what is the best route to take the wood through. What I mean is cut,...
I just bought a set of blue max and am very pleased. Fairly easy to put on with tool that came with them. My blade stays in place much better than it did with oem tires.
well I did what Derek had explained and for a 4 foot piece of plywood it was perfect as a tape measure goes. I am pleased. 6.5 inches on each end. Not dealing with very small tolerances on a daily...
Curious as to what number is considered very good in a table saw setup. My blade is just about dead on as far as the blade to the miter slot but miter slot to fence is about .003 off. I mean that...
I feel your pain on moving heavy objects. My shop is in my basement with no outside door. My table saw weighs around 750 lbs, my joiner weighs around 325 and they all came down the steps with a...
I see the error in my post. Yes I was thinking but not writing (or typing) lol.. My main intention is to be able to make box joint on the router. My table saw has a 1" spindle and the blade set...
Wondering if anyone has one and if so what kind of jigs have you made for it and how. I bought one because it was a great deal. $100 bucks. But I am probably overthinking the jig part.