Search:

Type: Posts; User: Brian Knop; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    1,106

    Thanks for the help

    Thanks for the help
  2. Replies
    7
    Views
    1,106

    Veneer substrate

    So I need a 15" wide cherry board for a secretary desk but I can't find anything in my area that wide but I do have 16" figured cherry veneer. Problem is I need 7/8" thick wood and no one that I have...
  3. Replies
    7
    Views
    875

    Yes I figure someone drop it. I sent an email to...

    Yes I figure someone drop it. I sent an email to Leigh, hopefully I can get replacements other wise it just junk.
  4. Replies
    7
    Views
    875

    Yes I just looked at the bracket and they are FAR...

    Yes I just looked at the bracket and they are FAR from square.





    +
  5. Replies
    7
    Views
    875

    Leigh D1285 Dovetail jig

    I bought a used D1258 and got the upgrade kit for making single pass dovetails but I'm having a hard time with it. Looking at the fingers and to me they should set flat or flatter then they do....
  6. Replies
    1
    Views
    702

    Finishing Secretary desk

    I’m about half way done building a Secretary deck with lots of pigeon holes. Trying figure out the best way to finish it. I like Shellac but don’t believe it’s a durable enough finish for a desk....
  7. Thread: Wide Cherry

    by Brian Knop
    Replies
    17
    Views
    1,965

    Irion has 150 BFT minimum for shipping. Don't see...

    Irion has 150 BFT minimum for shipping. Don't see that being very economical living in West Washington. I may end up going with veneer.
  8. Thread: Wide Cherry

    by Brian Knop
    Replies
    17
    Views
    1,965

    Wide Cherry

    I need a 16" wide piece of cherry for a slant secretary desk. Any recommendation for a supplier?
  9. Replies
    2
    Views
    5,476

    Lonnie Bird Secretary desk question

    So I'm building this desk, the writing surface is 7/8" thick and the lid is 7/8" thick and the two are hinged together, meaning that they should pretty much match up. The top drawer is lidded and...
  10. Replies
    3
    Views
    507

    Hinges are from Horton and Brass look just like...

    Hinges are from Horton and Brass look just like the ones Mark shows. But I think a mock up is a good idea.
  11. Replies
    3
    Views
    507

    secretary deck hinge locations

    Need to location the hinges for the slant top on the Secretary desk I'm making and I really don't want to screw it up. I little advise from someone who has made one would be appreciated.
    Thabks
  12. Replies
    8
    Views
    874

    Problem with DeWalt DW733 Planner

    It is leaving a high spot the length of the board 1/8" wide and maybe .030 high. Thought it was the cutting knives but I installed a new set same thing.
  13. Replies
    11
    Views
    1,124

    Well maybe I'll gorilla glue in a piece of wood...

    Well maybe I'll gorilla glue in a piece of wood to plug the slot and then use it for my 45 degree insert that way it will cut a slot in a different location in the insert. I'll just make a new one...
  14. Replies
    11
    Views
    1,124

    Tablesaw insert recutting

    I have a Phenolic tablesaw insert that I would like to fill in the saw slot and then recut. Anyone know what to use for this?
  15. Drilling a hole would provide strain relief in...

    Drilling a hole would provide strain relief in the corner just like with metal but not sure what to use to drill a hole in glass. I'll have to research that.
  16. cutting glass for Tall hood door ( or dial door)

    Ok Been trying to cut out 1/8" pane glass for the hood door but keep breaking the glass. Having problems with 1"cut back on the arch. I make the inlet cut with a diamond wheel but as I try cutting...
  17. Replies
    5
    Views
    865

    Finishing a secretary desk

    So what is a good way to apply the finish to a secretary desk, with all the little pocket holes? I like Shellac and or Lacquer.

    Thanks
  18. Replies
    0
    Views
    3,508

    Plans for Reclining Morris Chair

    Trying to find plans for a Reclining Morris Chair. Just think it would be faster then spending my time figuring it out the reclining part. Looking to add a metal recline mechanism for the legs. Thanks
  19. Replies
    11
    Views
    1,376

    Cherry veener source

    I'm looking for some figured cherry or crotch lumber and or veneer. Anyone have a good source?
    Thanks
  20. struggling with pore wood filling with shellac

    Finishing a Tall clock made from Walnut and have been trying to fill the pores with shellac with is what the finish is. I have been working at it for awhile LOTS of coats and sanding down and...
  21. Replies
    4
    Views
    2,465

    Thanks I have been trying to fine a book that...

    Thanks I have been trying to fine a book that could give a little bit of instruction and my local Library has Carving 18th Century American Furniture Elements, I just placed it on hold.
  22. Replies
    4
    Views
    2,465

    V-Gouge for Finial

    Anyone ever make a finial like this one? if so what size V-gouge did you use. There are 24 segments around a 2.75" finial.355479
  23. Replies
    5
    Views
    1,319

    That sounds pretty good. Gluing that is. I was...

    That sounds pretty good. Gluing that is. I was going to build a small steam box so as to pre-form the top piece in to the required curve anyways , then glue in place using hide glue, should be little...
  24. Replies
    5
    Views
    1,319

    Newport style Tall Clock

    Anyone here ever build one? My question what is the best way to attach the 1/8" thick (I'm using Walnut) curved cover on the top of the Hood. Cut nails or maybe small countersunk screw in a dark...
  25. Replies
    5
    Views
    1,542

    But that's a 20" dia bag which is my problem,...

    But that's a 20" dia bag which is my problem, can't find any 18"
Results 1 to 25 of 156
Page 1 of 7 1 2 3 4