Search:

Thanks for all the input. I do agree a lot of my issue is my process. These parts are riser boxes and treads for a stacked stair assembly for a sea ray yacht. I am attaching the 4 step unit together...

I am working on a project with a lot of holes up to 1” dia that have to match up for connectors. I have a 30+ year old craftsman 15” drill press and have had trouble with hole alignment. I replaced...

Thants for all the info. I ended up getting 2 jet 1000 cfm from acme tool on sale for 23% off after I missed the Black Friday jet 20% sale. Haven’t mounted them yet. May take a few weeks before I get...

Thanks for the ideas. I was going to get rid of the delta because to clean the filters you have to remove the ends of the unit and you can only blow then out with an air hose each end has a plastic...

I need to replace my air cleaner in my new shop. Old one is a delta triangle 400 cfm. The new shop is 20 x 40 x 12. At 6 ach I need 1000 cfm. At 8 ach I need 1300 cfm. The jet is 1000cfm and on...

Does anyone have any experience with this kaercher nt 30 vac https://www.kaercher.com/us/professional/commercial-vacuums/wet-dry-vacuums/nt-30-1-tact-te-hepa-11482160.html A few reviews and YouTube...

Steve. I second Jim. I’d call Harvey. They didn’t charge additional shipping when I called and ordered a shaper with a sliding table accessories. As long as I let them ship together they only crated...

Brent. Great info. Does a rebate cutter cut on top, bottom and outside face of the knives. I assume it does, just confirming. Do they make a guide bearing of the same od to use it as a pattern...

Follow up. How does it work buying from Whiehill and shipping to the US. Shipping and exchange rate. Do just let the CC company handle it. They have the knife profile. #1155745. Would need to buy...

Thanks for the info. To clarify I am looking this profile. https://www.grizzly.com/products/grizzly-6-pc.-stile-rail-set-quarter-bead-3-4-bore/c2165 Need a 3/4 bore this is my first purchase for a...

I am looking for a shaper reversible stile and rail set with a 1/4 round for some cabinet doors. I can only find the multi piece set. These are a lot more than a reversible any ideas?
thanks
gary

I use this one from Home Depot and like it. I tried the purple hf gun and think this one is much better
https://www.homedepot.com/p/Husky-Gravity-Feed-HVLP-Spray-Gun-H4840GHVSG/203497519

gary

I am trying to finish my new shop dust collector install and found that my grizzly 20” planer connector is and 5 1/8 od.
I can’t get a 5” hose over the fitting. I can get it on the hammer saw and...

Check the g1029. It’s the older 2 bag 2 hp with push button on/ off. Here’s the parts break down
https://cdn0.grizzly.com/partslists/g1029_pl.pdf
Gary

I am close to completing my new shop. Putting in the Harvey 700 dust extractor with 6” inlet. The local price for 6” sdr pipe and fittings just for main runs and drops, no blast gates hose or...

I would make sure the feather board is not past the front of the blade. It’s a bad deal to have the feather board pushing the wood against the left side of the blade and the right side piece between...

I did this last year and don’t remember exactly how I did it but know it was a pain until I found a trick. I removed the blades and the dust chute so that I could get to the back side from...

So in my hobby shop I have an older griz 1029 2hp dust collector. All 4” duct system. Only one machine at a time. Biggest is 20” planer and also longest draw (about 45 ft). Works good, no clogs no...

I have a griz 2 hp 1029 dust collector. It’s about 14 years old. Can I take the horizontal shaft motor and blower assembly and rotate the motor vertical to connect the blower inlet to the top of a...

Thanks for all the input. I am going to use 2x6x 12 fir studs. The current shop/garage has 10ft walls. We have decided to go 12ft on this new shop looks like code will allow 24” spacing so that’s the...

So I am ready to start framing my new shop this weekend. 20x40 stick frame on slab, Hardie siding shingle roof. Was going to do 10ft walls. Now thinking 12 ft tall. What’s the best way. Using 2 x 4...

Living with Texas coast humidity and temperature swings the magnetic material clings tight enough to the metal surfaces to eliminate the surface exposure to the air and also provides enough of an...

Hardin/Jefferson co to line. I cover all my machine surfaces with magnetic sign material from amazon. Stops all rust. Easy to do
gary

I live on the east Texas gulf coast. Very high humidity and condensation in a uncontrolled shop. After years of Johnson’s paste wax and total rust bloom about twice a year because I didn’t apply the...

In my current shop I have a griz 1029 dust collector connected to Table saw with a hose on the floor running to the wall then connected to A vertical pipe as part of the rest of the system. It works...