Search:

Type: Posts; User: Jim Andrew; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    22
    Views
    7,901

    I have the Oshlun, and it cuts fine, but mine was...

    I have the Oshlun, and it cuts fine, but mine was a little tight on the arbor of my Unisaw, so had my machinist buddy ream it slightly so it would slide over the arbor. He said he only took off...
  2. Replies
    18
    Views
    592

    You didn't post your age, which has something to...

    You didn't post your age, which has something to do with this question. I bought a MM16 15 years ago, and have not used it hard enough to hurt it. I use it for feet on my chests, once in a while I...
  3. Replies
    12
    Views
    598

    I used to save scraps, then got a bandmill, and a...

    I used to save scraps, then got a bandmill, and a wood furnace, and no more problem. Do save the better looking scraps thinking it would make a nice raised panel, but a neighbor asked me for scraps,...
  4. Replies
    27
    Views
    1,151

    If you are going to go through with this...

    If you are going to go through with this fabrication, make the cyclone body the same size as the ones sold by Oneida and other companies, with a long cone, as the 18" diameter seems to work very...
  5. Replies
    8
    Views
    349

    A neighbor brought all the damaged cabinets he...

    A neighbor brought all the damaged cabinets he bought at the re use it store to my shop for repair. I patched them up and he installed them in his house.
  6. Replies
    34
    Views
    1,834

    When I was getting ready to install the wood...

    When I was getting ready to install the wood floor in my shop, they had the flooring stapler for 90.79. So I bought it, used it, and it still worked when I was finished. A lot of their merchandise...
  7. Grizzly industrial

    Grizzly industrial
  8. Replies
    16
    Views
    535

    Before they came out with the rolls of foam, they...

    Before they came out with the rolls of foam, they sold rolls of fiberglass insulation, so if you prefer fiberglass to the foam, just cut some R11 into strips the width of your sill.
  9. Replies
    8
    Views
    581

    If you have a place to heat the wood, about 150...

    If you have a place to heat the wood, about 150 degrees F for a few hours will kill all the bugs and the eggs.
  10. Replies
    38
    Views
    1,724

    I sawed some for a friend, it had green spots and...

    I sawed some for a friend, it had green spots and dry spots. When I hit the dry spots, the mill about died. The blade would just stop cutting. Finally got through it, but was nasty. If it is...
  11. Replies
    6
    Views
    539

    If you know any contractors in the area, you...

    If you know any contractors in the area, you might ask to pick up a used suspended ceiling when someone is doing a remodel of a commercial building, as the ceilings and the 2x4' troffer lights...
  12. Replies
    27
    Views
    1,151

    Why not just buy the SSD XL 6" for 240$? Might...

    Why not just buy the SSD XL 6" for 240$? Might also check with ebay as someone used to sell a sheet metal cyclone on there.
  13. My K3 hose went bad soon after receiving it, and...

    My K3 hose went bad soon after receiving it, and thankfully, it was just a standard 4" hose. The fitting on the saw required an adapter to use a 4" connection, so thought it might be a metric size...
  14. Replies
    18
    Views
    867

    I have both an edge sander and tiny open end...

    I have both an edge sander and tiny open end widebelt sander, and would hate to do without either. Use the edge sander on most every panel, top, frame, door, and drawer front, and use the round end...
  15. Depends on how fresh you cut it.

    Depends on how fresh you cut it.
  16. Replies
    18
    Views
    893

    I have a central furnace and air in my shop, used...

    I have a central furnace and air in my shop, used the units from the house when upgrading to new, they are both high efficiency, although not nearly as high as the new mini split systems, so was...
  17. Replies
    19
    Views
    604

    Yellow pine is a kind of kinky wood, have seen...

    Yellow pine is a kind of kinky wood, have seen floor joists move after being installed, so would look at a hardwood. Made a router top from ash years ago, and it has stayed flat, but put finish on...
  18. Replies
    38
    Views
    2,476

    Bill, would not some water make your dust bin...

    Bill, would not some water make your dust bin pretty heavy?
  19. Ash is a sticky hardwood, and you need lube to...

    Ash is a sticky hardwood, and you need lube to cut it, or the stuff sticks to your blade.
  20. Replies
    3
    Views
    733

    There is a lot of discussion on Forestry Forum...

    There is a lot of discussion on Forestry Forum about this issue. The Wood DR Gene Wengert posts there.
  21. Replies
    10
    Views
    652

    Clearvue sells just the parts you need if you...

    Clearvue sells just the parts you need if you already have a cyclone like the one above. Just order the motor, impeller, housing and whatever details you need to move up to a 5hp system. If I were...
  22. Replies
    3
    Views
    275

    Lumber yards sell firring strips, so you don't...

    Lumber yards sell firring strips, so you don't have to use 2x4's, both in 1x2 and 2x2. You can use construction adhesive against the concrete to cut down on fasteners.
  23. Replies
    10
    Views
    652

    Chips from a jointer or planer are the easiest to...

    Chips from a jointer or planer are the easiest to collect. Sanding dust is the hardest, so figure that into your problem. If you do your sanding outside, maybe you can get by with a small DC.
  24. Replies
    33
    Views
    1,426

    I got the first 4" shark guard Lee built. My...

    I got the first 4" shark guard Lee built. My Hammer saw comes with a 2", and the truth is I can not tell the difference in the way they work. The Hammer sucks up thin strips, and the Shark will suck...
  25. Replies
    18
    Views
    893

    You might need to blow out the coils on your...

    You might need to blow out the coils on your dehumidifier.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4