Any makeup air should go through some filters to keep out mice, snakes, bugs and flying insects. Exhaust air ducts should also be screened to keep out bad stuff when the fan is off.The heat...
Type: Posts; User: Bill Dufour; Keyword(s):
Any makeup air should go through some filters to keep out mice, snakes, bugs and flying insects. Exhaust air ducts should also be screened to keep out bad stuff when the fan is off.The heat...
WW2 vets have a harder time. there as a big fire of ww2 records and the VA pretty much has to take any paperwork a ww2 vet can come up with. My Civil war vet Great grandfather has better records...
AFAIK you have to make your own nut cage etc to make it a self ejecting drawbar. R8 tends to fall out on its own. Most other milling taper sare much more angled and tend to fall out on their own....
Probably too cold in your area but I would think rainbow eucalypus would have varying coloring.
Bill D
If you were paying to use Kluber grease you would be using as little as possible. Probably cheaper to buy a used motor with good bearings then the grease.
A one kilogram can on Amazon is $429. ...
My Jet Mini mill is mt3 with a drawbar. Probably made around 1976.
BillD
Any relation to the safety speed cut panel saw?
BillD
If so then it should be confiscated and sold since it was used in the crime. They do that for drug dealer cars don't they?
Bill D
Some machines use zerks but they expect you to pump oil into them. Using grease will gum up sliding ways and cause wear. A properly greased bearing has about 30% grease 70% air in the open space....
Probably none. Unless you want to remove the endcaps so the old grease can be cleaned away before running the motor. You say it has grease zerks. Does it also have drains/vents to allow the old...
There was a thread about the correct name of this hardware in the last few months.
AFAIK most Simpson hardware can be ordered in stainless. Or just buy SS strap and cut /drill to need.
Bill D
I thought they used to be brass? Not brass plated.
Bill D
Some older jointers were direct drive. What rpm did the turn? Some direct drive bandsaws had odd low speed motors like 900 rpm.
BilL D
Was this the factory motor? I would guess around 3,500 for the cutter head so a cheaper high speed motor would be used from the factory. A high speed motor will also save a few cents in shorter...
Get a hardened nut that will slip over the shaft. Grind away most of one end to leave two little ears to fit the slots. Use a socket to turn the nut. Fill the socket with paper towel so you are...
I would buy and use. a pair of cheap needle nose pliers before going for too much hammering. Grind the tips to fit the slots on end. Use a big crescent wrench or pipe clamp to turn the handles....
Looks like you need something similar to a crowsfoot wrench down there.
Bill D.
If that is metal a company like western roller could mold on new rubber and grind it down to round. They redo planer outfeed rolls.
Bicycle grip tape, hockey stick tape.
Bill D
Never heard of it.
Bill D.
https://www.northfieldwoodworking.com/radialsaws/unipoint.htm
The drawback to any integrated shank is if you get another machine. If that machine uses a different spindle you will have to buy all new tooling not just switch arbors. Not really an issue for DPs...
Tabs at the back does make more sense. I have seen little nubs sticking out that go into the vertical wall of the slot at the back. Similar to the dowel pins for dining table leaves.
Bill D.
I have seen them with two little strips attached to the bottom front. The insert is placed front end down with the strips under the table. Then the rear is dropped to flush.
Bill D
Marble will be eaten up by acids. Granite will take most anything.
Bill D
You are not trained or paid to be an inspector or assessor. Let them do their job, if it benefits you with lower taxes.
Bill D
Climate? I understand frost will cause it to die back aboveground.
Bill D