Search:

Type: Posts; User: Izzy Camire; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    363

    What Jim mentioned about low humidity in the shop...

    What Jim mentioned about low humidity in the shop is correct. In addition I put this up by myself and I figured the weight of it was considerably less than sheet rock. At this point it has been up 4...
  2. Replies
    16
    Views
    363

    https://www.sherwin-williams.com/painting-contract...

    https://www.sherwin-williams.com/painting-contractors/products/problock-interior-oilbased-primer
    Thanks for all the replies. It seems like there is some leeway it what can be used. The above link...
  3. Replies
    16
    Views
    363

    Priming OSB

    Hi Folks, I am getting ready to paint my shop. The first step will be to apply primer to the OSB. I have the rough side out so no waxy stuff to worry about. Just wondering if anyone has done this and...
  4. Replies
    25
    Views
    1,179

    Congratulations now you can work on the things...

    Congratulations now you can work on the things you want to do.
  5. Replies
    29
    Views
    1,704

    I also use Duckduckgo and like it.

    I also use Duckduckgo and like it.
  6. Replies
    9
    Views
    669

    Mark, welcome this forum is a great place to...

    Mark, welcome this forum is a great place to learn. Folks here always have good suggestions for problems.
  7. Replies
    8
    Views
    657

    Hmmm move to AZ have to think on that! After...

    Hmmm move to AZ have to think on that!

    After more thought the paste wax with thinner sounds easy to give a try.
  8. Replies
    8
    Views
    657

    Thanks for all the ideas. The flax oil seems...

    Thanks for all the ideas. The flax oil seems promising to me.
  9. Replies
    8
    Views
    657

    Vise handle

    Hi Folks,
    I was wondering what those of you with a Benchcrafted vise and a shop that is not climate controlled have done on the vise handle to prevent rust. Benchcrafted manual suggests linseed oil,...
  10. Replies
    5
    Views
    980

    There was a value in the menu system that was 400...

    There was a value in the menu system that was 400 and it should have been 320. I am not sure where it was located in the menu. Wish they had put some thing on their website.
  11. Replies
    5
    Views
    980

    We finally got Laguna tech support on the phone....

    We finally got Laguna tech support on the phone. They knew right away what the problem was. I guess they saw it before.
  12. Replies
    5
    Views
    980

    Yes Ted you are correct it is off 2.5" on the 10"...

    Yes Ted you are correct it is off 2.5" on the 10" Y dimension.
  13. Replies
    5
    Views
    980

    Laguna IQ offsetting dimensions

    Hi Folks,
    We are trying to get the IQ to run a simple program correctly.

    The program locates 2 holes at:
    X: 4.0 Y: 1.0
    X: 4.0 Y: 10.0

    We have an origin setup at the corner of the work...
  14. Replies
    31
    Views
    1,906

    A year ago we installed a Delta Cassidy that we...

    A year ago we installed a Delta Cassidy that we are very happy with.
  15. Replies
    17
    Views
    1,201

    Well I finally got back to the shop. I decided to...

    Well I finally got back to the shop. I decided to take the advice offered in this thread. On both infeed & outfeed tables I put the edge closest to the planer bed at exactly the same height as the...
  16. Replies
    17
    Views
    1,201

    I got out to the shop for a few minutes this...

    I got out to the shop for a few minutes this afternoon. I turned the planer over and the casting is fine no problems. There is no access to the planer bed from there. Tomorrow I will readjust the in...
  17. Replies
    17
    Views
    1,201

    Thanks to everyone for their responses. I have...

    Thanks to everyone for their responses. I have picked up a few ideas and will look into them later in the day and make adjustments.
    I will start by turning the planer upside down and look at the bed...
  18. Replies
    17
    Views
    1,201

    I went to the Woodcraft and on their 735 the bed...

    I went to the Woodcraft and on their 735 the bed does not flex up and down. I this has a lot to do with the snipe. Could it have come unglued or something?
  19. Replies
    17
    Views
    1,201

    Dewalt 735 issue

    Hi Folks,
    I am having a snipe issue with my 735. I have the Dewalt infeed/outfeed tables. I have adjusted them so the outfeed table is above the planer bed and the far end of it is higher yet. My...
  20. Replies
    24
    Views
    1,581

    I have them on my saw and what has been said...

    I have them on my saw and what has been said about setting them before the fence is set is true. With that said I like them and feel safer and I feel the cut is better for using them. I would buy...
  21. Replies
    9
    Views
    629

    I tried to get a new belt at Applied Industrial...

    I tried to get a new belt at Applied Industrial and they could not get it. I called an online place but he could not get it but he did pass on some info. The belt on my machine is a Deyun Belt...
  22. Replies
    9
    Views
    629

    Nice mods to make it easier to tight end the belt.

    Nice mods to make it easier to tight end the belt.
  23. Replies
    9
    Views
    629

    Bill, thanks for the reply your point is well...

    Bill, thanks for the reply your point is well made. Perhaps a good quality belt will solve the problem. Izzy
  24. Replies
    9
    Views
    629

    Belt for G0490x

    Hi Folks,
    The belt on my G0490x has a memory on it causing a vibration. I am thinking of getting a new belt like a Gates. However I am also thinking of getting new pulleys and then putting on a...
  25. Replies
    16
    Views
    1,738

    I have a set of Barr bench/bevel edge chisels....

    I have a set of Barr bench/bevel edge chisels. They are the must rugged chisels I have.
Results 1 to 25 of 245
Page 1 of 10 1 2 3 4