Search:

Type: Posts; User: Todd Zucker; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Congrats on the shop! Please post photos.

    Congrats on the shop! Please post photos.
  2. I used West System g-flex epoxy for mortise and...

    I used West System g-flex epoxy for mortise and tenons on an outdoor table teak table in 2017. It sits in direct sun and gets rained on frequently and has held up fine.

    I used System Three T-88...
  3. Replies
    13
    Views
    1,294

    What thickness are the walnut veneers?

    What thickness are the walnut veneers?
  4. Replies
    3
    Views
    761

    John, those recommendations are very helpful. ...

    John, those recommendations are very helpful.

    Tom, I have not yet been successful spraying but am going to give it another try. Hopefully will have less user error on this attempt.
  5. Replies
    3
    Views
    761

    Transtint on farm table

    I am getting ready to finish a farm table with turned legs. The top and aprons are soft maple, and the legs are (unfortunately) rubberwood.

    For the top, I was planning to spray normal strength (1...
  6. Replies
    12
    Views
    1,273

    I am going to start a new thread on a similar...

    I am going to start a new thread on a similar topic relating to a maple table and did not want to hijack your thread.

    Having struggled with this last year, I do have a couple of comments.

    I...
  7. Replies
    49
    Views
    4,745

    I watched the video that Lee mentioned, followed...

    I watched the video that Lee mentioned, followed the steps and have no drift.
  8. The likely width of the 8’ dining table probably...

    The likely width of the 8’ dining table probably rules out the miter saw and the MFT for that project at least, unless you are gluing up portions and finishing with hand tools. If you go with a...
  9. Replies
    254
    Views
    25,129

    Mark, I do get your point. However, some of us...

    Mark, I do get your point. However, some of us have no formal training in woodworking and read books and articles and watch YT to learn a hobby we enjoy (which is not ideal). For us, there are...
  10. I started with a track saw and MFT, then added a...

    I started with a track saw and MFT, then added a band saw and jointer/planer. Then switched to mostly hand tools for a number of years and recently bought a Kapex and table saw. The track saw, MFT...
  11. I subscribed to his Patreon channel last month....

    I subscribed to his Patreon channel last month. Nice work, and helpful to see how he uses the slider and that arbortech grinder.
  12. Really nice work. Looking forward to seeing it...

    Really nice work. Looking forward to seeing it finished.
  13. I took John’s comment as a compliment. I wish my...

    I took John’s comment as a compliment. I wish my shop looked that nice.
  14. Replies
    103
    Views
    13,506

    Thank you for that.

    Thank you for that.
  15. Replies
    74
    Views
    8,535

    In your drawing of the side view of the chair,...

    In your drawing of the side view of the chair, the mortises are tall parallelograms, and the mortises ends are not square or perpendicular to the leg itself. To me, the top and bottom of the...
  16. Fascinating, and nice work! I think your efforts...

    Fascinating, and nice work! I think your efforts also satisfied my appetite for a while, and I am really happy you undertook this. It looks like a lot of math.
  17. Thread: Home Desk

    by Todd Zucker
    Replies
    15
    Views
    3,975

    That is a beautiful piece. Congrats. I need to...

    That is a beautiful piece. Congrats. I need to look into the Rubio pre color.
  18. Amazing work. Thanks for the photos. This is...

    Amazing work. Thanks for the photos. This is inspiring.
  19. Nice work! Really nice shop in addition to the...

    Nice work! Really nice shop in addition to the Roubo.
  20. Replies
    18
    Views
    1,670

    Thanks for sharing. Nice seeing a profile of...

    Thanks for sharing. Nice seeing a profile of someone who creates his own path.
  21. Replies
    14
    Views
    2,581

    Really nice work.

    Really nice work.
  22. Replies
    14
    Views
    1,550

    I did get a lifetime supply of the Torx screws...

    I did get a lifetime supply of the Torx screws when I took apart the crate.

    Jim, the high ceilings are great except when I need to change the fluorescent light bulbs.

    For outfeed, I might try...
  23. Replies
    11
    Views
    1,349

    Skating away,on the thin ice of a new day…

    Skating away,on the thin ice of a new day…
  24. Replies
    14
    Views
    1,550

    K3 delivery and placement

    Steve Wurster kindly posted photos of his workshop showing how he fit the K3 in a shop that had similar equipment to mine.

    Based on that and some other posters' comments, I went with the K3,...
  25. You’re not kidding.

    You’re not kidding.
Results 1 to 25 of 237
Page 1 of 10 1 2 3 4