I notice that the phone number listed on the Woodmaster website is out of service. Can anyone confirm that they are still up and running.
I would like to be able to talk with a sales person on the...
Type: Posts; User: Acharya Kumarswami; Keyword(s):
I notice that the phone number listed on the Woodmaster website is out of service. Can anyone confirm that they are still up and running.
I would like to be able to talk with a sales person on the...
Has anyone had experience with the Shop Fox 20 in. Belt Sander-W1709?
Thinking buying one in the future and hoping to get some feedback first.
Thank you.
Does anyone know if we can still get Lee Valley’s Ultimate Outfeed Stand?
I have one I bought nearly 20 years ago and would like to get another, but they seem to no longer carry it.
Otherwise, is...
Thank you. That's very helpful.
Can anyone tell me the length of the SCM outrigger tables. From photos, on all the mid-range saws, they seem to be the same length, which to me looks like 1500mm (measured from the blade). Felder has...
Can anyone confirm if the 1300mm outrigger on the Felder 700 series has a roller (like the 1500 mm does)?
Thank you. All this is very helpful.
Hi Larry. Thanks for the help.
I'm trying to figure out how much room I need to allow to the right of the SCM, since I need to position the machine next to a wall. If necessary, I can cut a hole in...
That makes sense. What about horsepower. How much?
SCM seems to offer the Nova in 6.6 and 8ph.
You prefer the Tersa over the Xylent” spiral knife?
Anyone have experience with the SCM Nova 520 jointer?
I am comparing it to the Felder A52L for a purchase.
I'm leaning toward the SCM machine.
Any thoughts would be appreciated.
Thanks.
Planning to buy a Felder A951 L Jointer at the end of the year and wondering about others' experience who own and use that machine.
Any problem with aligning the tables and keeping them in...
Is it correct that if you do lift it off the table that it required recalibration?
Is calibration in this case a simple matter?
Thank you Mark. Any experience with the Felder DRO rip fence for someone planning a 700 series saw purchase and picking out features?
Does the Felder rip fence DRO also cause loss of the ability to completely flip the fence out of the way?
It sounds like the answer is yes, but just to confirm, as I do need that feature.
Does anyone know the upcharge for Digital readout on the Felder KF700 rip fence when ordering a new machine?
Any experience out there with this feature?
On my current machine, an SCM Minimax 300 cu with 60" slider, came with no dust collection on the blade, though there is a 2" port on the shroud that attaches to the riving knife. that has always...
Thank you. This is helpful. I have come to the same conclusion and have made some pretty major changes in the shop to accommodate keeping the outrigger and fence on the machine all the time. But we...
I'm wondering if there is a way on the KF 700 to cut a piece of plywood in half. I realize the overhead dust collector would be in the way. It looks like that would be cumbersome to remove. But if it...
Thank you Mark.
Best regards
Acharya
Hi Mark
In this thread a while back you mentioned; "You can cut the [crosscut] fence down to a point, I think maybe 6”-9” on the 1500 maybe more on the 1300."
I think I would like to plan on doing...
Thank you. Yes, the upcharge turned out to be less than I thought for the 10hp: $484.
I'm also looking at a KF 700, which as standard is also equipped with 5.5hp.
Any advice on best motor sizes...
Can any Felder folks verify whether a Felder AD 951 can be purchased with a 7.5 hp motor, and what the upcharge for that is?
I am told it is only available in UK, but it's in the catalog. It was...
I understand that the 951 is NOT available with Mobility kit.
However, can it be moved conveniently with a pallet lift?
In my case, I would have it near a wall and moved it parallel to the wall...
Thank you, Erik.
Yes, it's good concrete.
That's very helpful!