When you pour the Epoxy first pour a seal coat. Lightly run a flame over the entire top to have the trapped air bubbles gas out. Careful not to burn it by keeping the torch in one spot too long. Then...
Type: Posts; User: Brian Schursky; Keyword(s):
When you pour the Epoxy first pour a seal coat. Lightly run a flame over the entire top to have the trapped air bubbles gas out. Careful not to burn it by keeping the torch in one spot too long. Then...
Nice Job looks great.
When's the party? LOL
I'm sure you can wipe it on. I tried on the arm rail but I wanted it thick.
I first tried with a sponge type tool but had my best luck with a good soft brush....
Hello and how are you?
I did 7 layers of Varnish/reducer mix adding less reducer with each layer. Sanding between each layer and wiping down with the Behlens reducer. The reducer is not just mineral...
Hey thanks Jim. It was the boss lady's idea.
Always laugh at your Red Buttons Quote:)
Good Morning Everyone,
It has been 10 months with the Bar. It's still working out very well. Before a party I hit the top with some Windex and then some cheap car polish (non abrasive) and it's...
Yes they are right about spar varnish.
I used Behlens Rock hard table top varnish. I thinned it with their own thinner. When I couldn't smell it anymore I knew it was dry.
Hi Everyone and good morning.
It has been a few months and a few parties since I had finished the Bar project.
The top is going strong. It handles any party....
Hi everyone. Hope life is good for you all.
Finaly got to put the pole up.
http://farm4.static.flickr.com/3014/2566710594_4ea8e6492d.jpg
How goes it?
The Bar is done. Just got to add the little extras.
http://farm4.static.flickr.com/3261/2532875716_4f58125ff3.jpg
http://farm3.static.flickr.com/2215/2532059297_18d2f8c086.jpg
...
Hi Everyone,
Next week it will be a month after I put on the Behlen's rockhard. I had put 7 layers each cut 10% with the reducer and sanding 48 hours after each layer. When will it become hard so...
Hi Robert,
Is it possable to get a high gloss shine with higher grit and then polish?
I have a obital sander but I cant find sand paper with high grit. I do have flat square sand paper that will...
Hi Robert,
Nice on the Varnish top. How did you get that high gloss shine? Did you start by sanding and what grit. What was the last grit and did you use polish? The reason I ask is because I...
Hello People,
How goes everything? I finished using the Behlen's Rockhard cut 25% with the reducer. I put down 7 layers sending with 320grit every 2 days. Now I'm going to let it sit for 3...
Hay Per how are you these days?
Thanks for the reply. I had tried a small peace of hand rail with varnish a while back using 800 then 1000, 1500, 2000 and finaly 2500 grit sandpaper. Car compound...
Hi Everyone,
Hope you are all well?
It's been a few weeks for the epoky to air out. It looks better than my trial runs. Time for the Behlens Varnish. the question is when I sand the top with 220...
Hi Everyone,
Hope all is good. It's the Bar is getting there. The Epoxy is done it came out better than my trial runs. When they say 70-80F they mean it. My trian runs were to hot. As per Per at...
Hi Everyone,
Hope everyones good. Don't forget Happy Easter.
I got a few days of from work so I poured the Epoxy on Friday.
A few pics...
Hi Joe,
Try to switch from your current setting to Linear Mode under Display Mode all the way to the right side of the thread heading.
Brian
Hi Joe,
I get that too. If I view the thread without signing in it's ok, but when I sign in and view the same thread I loose the pages and have to scroll down that first box thing.
...
Hi Everyone,
Doe anybody know where I can get my hands on sheets (9 x11) or so of sandpaper? Hi grit 1500 and 2000. On line or I'm located 10 mile North ov NYC.
...
Hi guys,
what do you guys think of the Makida Model #BO5012?
Brian
Hey thanks guys. My Makita is a BO-5010K (?) I think without looking at it. I had got it a few years ago (Quickly) to work on a fooseball table. No it doesn't have a varible speed control. Makita...
Hi Guys,
How is everyone? I spoke to Phoenix Epoxys whom is the laboratory for Mas epoxys and they agree with me about 3 gal of resin and hardner to cover 16sq ft taking in account the density...
Hi Everyone,
Hope everybody is good?
Question just had a birthday and got a bunch of Homedepot gift cards. Is there any type of homedepot powertool that can act as both sander and polisher/buffer...