Search:

Type: Posts; User: Cary Falk; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    34
    Views
    1,580

    I have never made them and had to do a search to...

    I have never made them and had to do a search to see what you were talking about so take my opinion for what you paid for it. My first hit on my search shows a rail and stile which is clearly...
  2. Replies
    70
    Views
    3,799

    I have never felt 5hp was not enough on any of my...

    I have never felt 5hp was not enough on any of my tools. I am not a business. The largest cutter I spin is a Freud carbide insert raised panel cutter. I usually take multiple cuts at slower feed...
  3. Replies
    6
    Views
    389

    I always go with outer stiles at full length and...

    I always go with outer stiles at full length and inner stiles go between the rails. I do it so I don't see end grain on the sides. As mentioned, it probably doesn't matter.
  4. Replies
    70
    Views
    3,799

    Looks nice but it is 3phase and 400 miles away...

    Looks nice but it is 3phase and 400 miles away from OP.
  5. Replies
    70
    Views
    3,799

    I have the Laguna Pro 5hp. I had a Grizzly 1026...

    I have the Laguna Pro 5hp. I had a Grizzly 1026 before. I believe a shaper lives and dies by the fence. I love the fence on the Laguna and hated the one on the Grizzly. The Oliver fence looks...
  6. Replies
    24
    Views
    1,877

    I love hard maple for so many reasons. I can't...

    I love hard maple for so many reasons. I can't think of one thing that I hate about it.
  7. Thread: Dowel Pins

    by Cary Falk
    Replies
    24
    Views
    2,226

    You can put them in the microwave for 30s to get...

    You can put them in the microwave for 30s to get some of the moisture out and shrink them somewhat. Past that, they might just be oversized and you might need a dowel plate or sand them down.
  8. I had a 513x2 and now have a Laguna 18hd. I...

    I had a 513x2 and now have a Laguna 18hd. I bolted a piece of 1.5" square tubing on the long side of the base through the holes already there. The tubes ar long enough to bolt a 3" stem caster on...
  9. Replies
    22
    Views
    1,913

    I have 20 tape measures and 100 pencils around...

    I have 20 tape measures and 100 pencils around here somewhere.
  10. Thread: Sandpaper

    by Cary Falk
    Replies
    22
    Views
    1,867

    Sheet sandpaper comes from Home Depot. Sanding...

    Sheet sandpaper comes from Home Depot.
    Sanding disks come from Amazon.
    Drum sander paper comes from Industrial Abrasive.
  11. Track saw - this is pretty much a one trick pony...

    Track saw - this is pretty much a one trick pony for me due to having other tools that are faster for me. I usually only use mine for breaking down plywood and then make final cuts on the tablesaw....
  12. I will go with not a commonly used tool. I have...

    I will go with not a commonly used tool. I have one but I don't use it very often.
  13. I have cut some 1/4" plate. The thickest piece...

    I have cut some 1/4" plate. The thickest piece was a pommel and guard for a viking sword which was about 1" thick. I cut the pocket for the blade with an 1/8" end mill. My cuts are always very...
  14. Replies
    9
    Views
    720

    If it is going to be painted I don't see why not....

    If it is going to be painted I don't see why not. I would use a finger joint bit and alternate the short cut ends as mentioned before.
  15. I have a 2019 Stinger 2x4 with a higher gantry...

    I have a 2019 Stinger 2x4 with a higher gantry and a 2.2k spindle. No issues cutting Aluninum but I take it slow. I don't do much of it because it is messy. I have a mister and use denatured...
  16. Replies
    6
    Views
    2,017

    If you are in the Portland OR area I can do it...

    If you are in the Portland OR area I can do it for you.
  17. Replies
    47
    Views
    4,601

    I'm glad I am not in the marker for a drill...

    I'm glad I am not in the marker for a drill press. If I was It would probably be the Nova Voyager. I'm not sure if the electronics will hold up for 20 years like you want. I'm not saying they...
  18. I had a 36" rip capacity on my saw before I got...

    I had a 36" rip capacity on my saw before I got a track saw. I now have a 36" rip capacity on my saw. I don't find a track saw as a replacement of a table saw.
  19. Replies
    79
    Views
    11,306

    I dove into the rabbit hole last year due to a...

    I dove into the rabbit hole last year due to a health issue. What I settled on was the following:
    1) Keep moving. A person that exercises but eat unhealthy will live longer than somebody that eats...
  20. Replies
    32
    Views
    2,972

    I made 3 orders before Christmas and all arrived...

    I made 3 orders before Christmas and all arrived promptly and without issue.
  21. Replies
    14
    Views
    1,248

    This looks like the best bet if you want to...

    This looks like the best bet if you want to replace. I looked for parts for the G01023RL and pricing the front rail, rear rail, and front tube it comes out to $360.
  22. Replies
    18
    Views
    2,533

    I made one that is a combination of the...

    I made one that is a combination of the Woodpecker, Veritas and the guy on Youtube that the Veritas one is based on. I made it mainly for picture frames. Mine will also allow for use of my standard...
  23. Replies
    10
    Views
    1,004

    I have always used Industrial Abrasive. They...

    I have always used Industrial Abrasive. They used to have larger rolls but now sell only 35' rolls which is a bummer. It is cheaper than Klingspor per foot but with the new shorter rolls I don't...
  24. Replies
    79
    Views
    11,162

    - 4 in one screwdrivers. I have a couple. Great...

    - 4 in one screwdrivers. I have a couple. Great for taking somewhere. The only thing don't like is the shaft is wider and it doesn't fit in a lot of places. I mostly use battery power...
  25. Replies
    25
    Views
    2,983

    I sold my Dewalt scroll saw because I just didn't...

    I sold my Dewalt scroll saw because I just didn't use it that much. It was by far the smoothest scroll saw I have used. Like everything else, the blade makes a huge difference. Those spiral blades...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4