Search:

Type: Posts; User: Steve Schoene; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.20 seconds.

  1. Replies
    2
    Views
    210

    Bob Flexner suggests using naphtha instead of...

    Bob Flexner suggests using naphtha instead of alcohol to remove the mineral oil lubricant from the final shellac surface. Just dampen a clean cloth and wipe the surface oil.
  2. Replies
    21
    Views
    839

    Coat the insides with shellacóa. couple of so of...

    Coat the insides with shellacóa. couple of so of 2 lb coats That will block any fumes from the wood and is fast.
  3. Replies
    5
    Views
    443

    Potassium dichromate solution will color oak...

    Potassium dichromate solution will color oak nicely. (!! poison use care !!) Birch has much less tannin and will just change color modestly. TEST scrap to determine desired concentration on your...
  4. Replies
    5
    Views
    443

    What wood is to surround the oak? In some cases...

    What wood is to surround the oak? In some cases chemical ďstainsĒ can impact the oak with little impact on something like maple.
  5. Replies
    10
    Views
    699

    It might take another coat or two to get pore...

    It might take another coat or two to get pore fully filled. Iíd want to do a few test coats on scrap of your hickory to test whether sanding finish coats is enough or whether a pore filler would be...
  6. Replies
    10
    Views
    699

    Hickory has open pores of medium size. Painting...

    Hickory has open pores of medium size. Painting without previously filling the pores will leave visible pits. The pores should fill fairly easily since the pores are much smaller than oak pores but...
  7. Replies
    3
    Views
    319

    I would avoid most finishes which would be less...

    I would avoid most finishes which would be less durable than the Corian material itself. Goggle Corian for exterior use.

    I donít think ca glue is very UV resistant and after all on nonporous...
  8. Carl. The problem you had is mostly with epoxy....

    Carl. The problem you had is mostly with epoxy. It is not very uv resistant for exterior doors. It can work outdoors if covered by multiple coats of marine grade spar varnish such as Epifanes. Iíve...
  9. A sheet of tempered glass will be sure to work as...

    A sheet of tempered glass will be sure to work as required. Asking finishes available outside of industrial facilities to work is questionable and likely to require regular refurbishment.

    Whatís...
  10. Replies
    6
    Views
    887

    Iíve found that hand planing works wonders. Itís...

    Iíve found that hand planing works wonders. Itís fast and can reduce sanding requirements to a very small amount. Itís just a few strokes to eliminate planer ripple.

    I also point out that the...
  11. If you donít spray Iíd go for a watercolor wash...

    If you donít spray Iíd go for a watercolor wash brush with very fine synthetic bristles. Windsor newton makes a good line
  12. I suggest rethinking the clear finish. First,...

    I suggest rethinking the clear finish. First, Minwax Spar Varnish is one of the least durable available. Gloss varnishes are generally thought to be more durable as well. For a good spar varnish,...
  13. Replies
    10
    Views
    1,832

    yes, stickers need to be dry.

    yes, stickers need to be dry.
  14. Replies
    9
    Views
    903

    Good advice

    Good advice
  15. Replies
    28
    Views
    2,457

    Smith (exact name escapes at moment) is a low...

    Smith (exact name escapes at moment) is a low viscosity epoxy designed exactly for this use. It’s available at Jamestown Distributors. It really adds durability since it reduces moisture and oxygen...
  16. Replies
    5
    Views
    485

    Naphtha is one good solvent for wax. Use plenty,...

    Naphtha is one good solvent for wax. Use plenty, and lots of cloths or paper towels.
  17. Replies
    8
    Views
    1,143

    Use dye not a pigmented stain.

    Use dye not a pigmented stain.
  18. Replies
    3
    Views
    520

    What does the technical data sheet for the white...

    What does the technical data sheet for the white lacquer say about primer? That's where to find the answer. Question your choice of lacquer if no techniocal data sheet is available--it's an...
  19. Replies
    4
    Views
    952

    For most dramatic figure start with dilute water...

    For most dramatic figure start with dilute water mixed dark brown powdered dye. After the dye has dried sand the surface so that where the wood is porous the dye penetrates deeply and does not sand...
  20. Replies
    4
    Views
    755

    Paint may be more durable but wood ladders should...

    Paint may be more durable but wood ladders should never be painted. Paint can obscure defects in the wood. This is a traditional rule not something I made up.
  21. Replies
    2
    Views
    912

    From the description it looks pretty much like...

    From the description it looks pretty much like most oil varnish mixes, except for rather breathtaking prices.
  22. Replies
    8
    Views
    1,048

    Pure tung oil will never, applied properly, yield...

    Pure tung oil will never, applied properly, yield a glossy finish, satin is the best to be expected. For that matter oil/varnish mixes don't do very glossy very easily. The reason film finishes...
  23. Replies
    8
    Views
    1,048

    Lets start with the wood itself. Red oak is not...

    Lets start with the wood itself. Red oak is not a good choice for the truck bed. It has open pores that can extend deeply into the wood, with the consequence that it is susceptible to rot. It's...
  24. Replies
    3
    Views
    557

    Itís not a problem to go straight to satin but it...

    Itís not a problem to go straight to satin but it could be somewhat hazy with multiple coats. Satin is also a bit thicker than the Original ie. higher solids content.
  25. Replies
    25
    Views
    1,562

    Titebond is not a good gap filler. If you canít...

    Titebond is not a good gap filler. If you canít find the right size drill bit you could use epoxy glue which is a much better gap filler. Itís not so easily reversible if thatís an issue. Itís also...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4