Search:

Type: Posts; User: Tom Hassad; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. thanks for the suggestions

    Thanks both for the suggestions.
  2. Laguna Bandsaw Plastic Blanking Block - do I need it? see pic

    461814

    I was having some bandsaw tracking problems and I think my blade ended up cutting this in half so I need a new one - did not see it listed on Amazon and was wondering how critical it is - I...
  3. I will have to check the specs but I think it has...

    I will have to check the specs but I think it has to handle 600 watts. I have 14-50 Nema plugs and I bought an extension cord and put a plug on the end of the 18 inch cord but the extension cord was...
  4. I took a picture of the cable and it mentions 12...

    I took a picture of the cable and it mentions 12 gauge/3 and elsewhere it mentions 600V but not sure if these other numbers help identify it. 444530
  5. The right power cord for Hammer A3-31. Jointer/planer

    Some of you may know that this very expensive power tool comes with an 18 inch power cord and It makes no sense for those who have no ability to place the machine right on top of an outlet. I did...
  6. Hammer mobility kit (rolling carriage) for A3-31

    Hi - I have reached out to hammer to figure out the part number for the rolling carriage. I found one in their website but it does not look exactly like the one featured in their official YT video...
  7. Replies
    9
    Views
    1,299

    Thanks got all the comments. I’m a bit relieved...

    Thanks got all the comments. I’m a bit relieved that this will work as a top. I’d prefer hard maple but it would be much harder to acquire. I’d have to travel out of town. I figured that it was...
  8. Replies
    9
    Views
    1,299

    Hard or soft maple

    This is the 8/4 lumber identified only as maple - I need to make a workbench top. Is this soft or hard? They are selling this at $5.89 bd foot where I live in so. Cal. 427512
  9. Replies
    9
    Views
    1,506

    Thanks for the suggestions - I will look at this...

    Thanks for the suggestions - I will look at this very closely this weekend and report back what I found/did.
  10. Replies
    9
    Views
    1,506

    I have the incra miter sled and both parts have...

    I have the incra miter sled and both parts have one miter bar each and I get more issues on one slot more than the other.
  11. Replies
    9
    Views
    1,506

    Sloppy miter slots

    I have a hand me down delta Unisaw and I think I have an issue with the miter slots. I have a miter sled that you can adjust to take out lateral movements when it runs in the miter slots but if I...
  12. Replies
    18
    Views
    2,776

    These are all great comments that I will refer...

    These are all great comments that I will refer back to as I make sure this fence is set up correctly and positioned correctly with the parts attached in proper order and alignment - thank you all.
  13. Replies
    18
    Views
    2,776

    I want to add that maybe I glued two board a that...

    I want to add that maybe I glued two board a that were not square because when after I jointed the one face I noticed that of the two boards glued together one side was thicker than the other side so...
  14. Replies
    18
    Views
    2,776

    I am using box store 2 by 6’s and ripping them to...

    I am using box store 2 by 6’s and ripping them to approximate width and then I joint the side (the thin edge) and I use that to but up against the fence while I joint only one face. I do that with a...
  15. Replies
    18
    Views
    2,776

    Frustrations with Hammer A3-31 fence

    Has anyone else here dealt with the jointer fence moving out of 90 degrees to the table? I planed and glued together two boards and then jointed and planed the assembled pieces to final dimensions...
  16. Hi Curt and others - I looked at the option of...

    Hi Curt and others - I looked at the option of putting my Bench dog Pro Max table on to this T/S. I had it attached to another table saw. I bought a cabinet frame for it and never got around to...
  17. Looking for ideas for replacing or losing my Delta Unisaw extension table

    I have the beisemeyer 52 inch rail system with a 34 inch long 27 inch wide extension table made of hardwood frame, particle board top and laminate on top of that. This saw with mobile base and...
  18. Brand name bandsaw bade advice needed for Laguna 14BX

    Hi I am probably asking a loaded question that will ignite a which product is better debate but I am getting a Laguna 14BX bandsaw and I did a very cursory search for bandsaw blades. I know Laguna...
  19. Replies
    18
    Views
    7,299

    I totally forgot about the fact I would be...

    I totally forgot about the fact I would be running another power tool and just thinking about the tool in isolation - that 85 or 76 db may be eclipsed by whatever machine is actually creating the...
  20. Replies
    18
    Views
    7,299

    I have now decided not to go with the Grizzly...

    I have now decided not to go with the Grizzly G0458 because I saw a YT video where the machine was emitting 93 db at the source and 86db just a few feet away. I rather pay more for something that...
  21. Replies
    18
    Views
    7,299

    Thanks for the advice - If I go with the 861 I...

    Thanks for the advice - If I go with the 861 I get the benefits of the cyclone but after tax and delivery and comparing it with the G0458 model I would be paying ~ 600 vs. ~1100 for the small...
  22. Replies
    18
    Views
    7,299

    Thank you. I am going to just wheel it over to...

    Thank you. I am going to just wheel it over to one of three machines, a cabinet table saw, 12 inch jointer planer and a 14 inch table saw, connecting and reconnecting when I go from machine to...
  23. Replies
    18
    Views
    7,299

    cyclone vs. Jet vortex vs. Grizzly cyclone

    I need a new dust collector and I am convinced I need a cyclone. I saw the new Grizzly units but they have virtually no YT reviews and the only videos I could find were complaint videos. I saw the...
  24. Thanks - I think I need to look into a new one.

    Thanks - I think I need to look into a new one.
  25. Does anyone have the PSI 1 HP collector - what is the CFM reading

    I have the Penn State Industries 1 HP with the cloth bags. I have not used it in over 6 years and I need to figure out if I upgrade to a cartridge filter and chip separator whether it will still...
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4