Search:

I get mine at Craft Supplies also
Craft Supplies USA
I would suggest that you go with steel, not the ceramic grinder. I have had a couple of the ceramic grinders break, I think they were set too...

The decision was made for me. The Grizzly was a free saw and I help a guy get it to his house. He is in the same boat, needing to decide if he want to restore it and sell off his Delta 14". He is...

I currently have two bandsaws, a 14" Delta clone that I keep a narrow blade on to do curved work and a Laguna 14-12 that I have setup for re-saw work. My dilemma is that I was just offered a Grizzly...

Our WW club gets these kind of messages on a routine basis. Some are complete shops with nice tools, but most are just run of the mill or low end tools that are hard to sell., Most of the time we...

This is the small section of my counter top and the bar top section
511582511583

I replace my countertops with wood. I used 1-3/4 x 7/8 stock and glued up edge grain, I think I used 29 pieces to get the width I needed for my counters. I finished them with tung oil, several coats...

No, my shop is limited to 110.

I have used this before and it worked well
https://www.homedepot.com/p/Varathane-16-oz-High-Performance-Wood-Hardener-340229/305626727

It seems to be very thin epoxy, it ran straight thru the...

I am very happy with the saw, I have had it for 6+ years and other than a couple of minor issues it has been a good saw. The plastic face on the fence wore so I replaced it with a piece of extruded...

I have a PM1000 table saw and the everyday blade I use is a 40t Tenryu Gold Medal blade. For ripping I use a full kerf blade most of the time, either an Amana or Rigid Carbide. I only change to a rip...

Also removing the impeller will save about 2 amps, less likely to trip the internal breaker.

My Dewalt is significantly quieter with the Steelex head than with straight knifes, still loud, but not nearly as much.

Ask over here on Scrollsaw Village
http://www.scrollsawvillage.com/

You do not want to waste your money on one of the new Excaliburs, the company was sold a few year back and the manufacturing was moved to China. The new saw are not made to the same quality as the...

I have used this one when I need to use an extension, which is not very often so I don't mind using two wrenches...

Whatever you do to fix this, I would do to both sides. The other side that appears good is probably a bit loose and fixing it will just add to the strength of the chair.

If you have the planer hooked up to a good DC just remove the impeller, you don't need it. It will also save a bit on power.

What temp/humidity is the wine room going to be kept at? The few I know that have cigars in their wine room just have a spanish cedar lined drawers with holes in it. The wine room temp and humidity...

It has carbide inserts for the cutterhead, watch the video

I am sure the PM 1420 is a fine lathe, but IMHO it is a very expensive small lathe. If you have never turned before I would suggest you buy a used Midi Jet/Delta/Rikon ect and see if you are going to...

I have used both powders and dyes from Alumilite and Alumidust. Both work fine, the one thing I will caution you on is don't use too much of the color. The first couple of times I did this I used way...

Remove the table and the motor if it sticks out, strap it to a 3/4" piece of plywood and use a dolly like the one above.

Maybe I am missing something here, but why not use a scrap piece of plywood with the the correct size hole you want drilled thru it and double stick tape it to the sheet and use a router with a...

The chisel looks to be a hollow grind, ground on a wheel. When you then sharpen the chisel on a flat stone the edge will only contact the stone at the top and the bottom. The chisel is sharp in your...

I was going to by this jig a while back but found this video. I have made several hinges and claps using this method
https://www.youtube.com/watch?v=3foxwJQRd60