Search:

Type: Posts; User: Adam Herman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    58
    Views
    2,162

    and not everything listed as QH compatible will...

    and not everything listed as QH compatible will fit.
  2. Replies
    12
    Views
    824

    I would do a bent lamination of VG DF or similar...

    I would do a bent lamination of VG DF or similar grained Ash with Kevlar or carbon fiber between the laminations, and wrapped around the outside at the critical hardware, with epoxy. I think it...
  3. Replies
    58
    Views
    2,162

    many implements have different distances between...

    many implements have different distances between the 3 pins, a std. quick hitch also requires the use of a bit longer pto shaft. at least on my branson, the Pats will nearly eliminate the need to...
  4. Replies
    58
    Views
    2,162

    I run grab hooks and a chain with one grab and...

    I run grab hooks and a chain with one grab and one slip. seems to afford me the most length and rigging options. I also have a hole from a PO in the bottom of the bucket that will fit a large screw...
  5. Replies
    196
    Views
    16,937

    good luck Jim! a feverish pace! My permit...

    good luck Jim! a feverish pace! My permit finally got unstacked from the bottom of someone's desk and was sent to the builder. now he is 2 weeks out. hopefully by June 1 I will have my shell up. ...
  6. Replies
    41
    Views
    2,739

    I'm planning to run Romex for the lights and EMT...

    I'm planning to run Romex for the lights and EMT surface mount for the shop portion. set up a laser in the middle, and start going around the shop at about 4 ft with quad boxes and sticks of 3/4....
  7. Replies
    196
    Views
    16,937

    what tooth bar did you go with?

    what tooth bar did you go with?
  8. Replies
    196
    Views
    16,937

    Nice! I'm still waiting on permits. :mad:...

    Nice! I'm still waiting on permits. :mad: hopefully yours go smoothly.
  9. Replies
    19
    Views
    1,182

    I have no experience on a river table, but rebar...

    I have no experience on a river table, but rebar seems like a poor choice. its low quality steel and it will only hold the epoxy, not the wood and is similar to a wet noodle unless its in something...
  10. a bit of ballast in the bottom may make them a...

    a bit of ballast in the bottom may make them a lot more stable, looking at the shape and weight distribution.
  11. Replies
    12
    Views
    1,079

    and remember you can increase your cost basis by...

    and remember you can increase your cost basis by doing capital improvements to the property. this is one of the keys to owning rental property for the value increase and not the rental income.
  12. Replies
    196
    Views
    16,937

    great jim! we are sitting here with a building...

    great jim! we are sitting here with a building in the yard of the contractor waiting on any word at all on our permit that was put in 5 or 6 weeks ago. and if you call they just say "its approved...
  13. Replies
    196
    Views
    16,937

    i have been really impressed with decoguard low...

    i have been really impressed with decoguard low sheen, a solvent based sealer that you can apply with a garden sprayer. it really soaked in and does not leave a slippery finish. does not seem to be...
  14. Replies
    196
    Views
    16,937

    yep. something about a pole barn, it just ends...

    yep. something about a pole barn, it just ends up being the "best" choice. I was dead set on a metal frame building at first, but it was just not going to work out with the extra concrete work for...
  15. Replies
    196
    Views
    16,937

    i think you came up with a very handsome look...

    i think you came up with a very handsome look with the stripe and tan bottom, even with the sub par material.
  16. Replies
    196
    Views
    16,937

    should be fun. I am a little further along, we...

    should be fun. I am a little further along, we got 144 ton of structural fill today. dirt work starts tomorrow on a 40x36 Lester pole barn with a 10 ft x 36 ft "porch" that will get the tin removed...
  17. Replies
    21
    Views
    2,782

    what wood is it on? any other finish steps,...

    what wood is it on? any other finish steps, stain, conditioner?

    if your wood choice can take it, you could set it out in the sun for an hour or 2. this does wonders to a slow curing finish for...
  18. clean out the collet and bit shaft with some...

    clean out the collet and bit shaft with some scotchbrite or similar. assuming it moved in the collet.
  19. oh damn, well fair enough! sounds like it could...

    oh damn, well fair enough! sounds like it could be a problem with the adaptor, but who knows. We have always used clipper creek stuff and have not had any issues.
  20. there is absolutely no reason to have a charger...

    there is absolutely no reason to have a charger with selectable max amperage. the car will only take what it can use, and will adjust to the charge curve of the battery. a higher amp capacity...
  21. just to make up the part left out, hard wired...

    just to make up the part left out, hard wired stuff follows a different standard than an outlet.
  22. :rolleyes: The charge adaptor on the wall will...

    :rolleyes:

    The charge adaptor on the wall will tell the car how much it can supply and the car will set its current limit to that number. this is one reason there are communication pins on the...
  23. Replies
    13
    Views
    830

    i installed this in our house about a month ago. ...

    i installed this in our house about a month ago. while I don't really see more "bars" on our phones, we do have better service. I can watch a youtube video in low quality now vs not getting them...
  24. Replies
    24
    Views
    1,391

    as far as painting, the best is to remove the...

    as far as painting, the best is to remove the door, and all hardware before finishing. I like to have to door completely done before it is hung. hang the door and trim it out, then remove door and...
  25. Replies
    24
    Views
    1,391

    pre-hang? heck yes. much easier install, more...

    pre-hang? heck yes. much easier install, more accurate machining possible, easy to install as well.

    I really can not see any advantage to not pre-hanging. which, to be clear, is the install of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4