Search:

I have a hammer sliding table shaper and a minimax J/P. Both single phase machines, about 4 kw, running at 240v.
The hammer requires the operator to hold the start button down until the motor...

Talked to Rol Air and they said they haven't made pressure lube pumps in 30 yrs. This pump may be that old, no way to tell.

I asked if he had an idea what speed they should run at, and he said...

Bill,
Thanks for the reply
I don't know if it is just me, but google gives a lot of garbage advertising first in their searches.
Try to find EL Smith compressors and it gives everything but.

My...

Tom King - See added attached photo. Much smaller than yours.
I have seen pump lists from major manufacturers who make pressure lube small horsepower, but they are expensive.

Found a new old stock twin cylinder pump with pressure lubrication locally, and now am trying to figure out what the best speed to run it at is.

I've seen 700 rpm mentioned.

The only name on...

saw is now running both motors via separate vfd's. VFD's reside in an enclosure with remote momentary buttons for stop and start. Still working on getting the original emergency off button...

Malcolm
Thanks for taking time to provide this clear and detailed response!
The parameters that allow remote operation (turn off the keypad) are in the bubble I copied from the manual, item 8.2, so...

Jared -
you know more about these than I do. The unit is described as having 50 amp output, so if halved, would be 25 amp. But this saw is replacing the Unisaw I have had for 15 yrs now that is...

It is a single phase input, 3 phase output. The motor is about 7.5 hp, the vfd is rated at 10 hp.

attached possible wiring diagram for remote stop start for Vevor vfd in lieu of original panel controls

suggestions advice appreciated

Have seen other diagrams where the output of the momentary...

Matt,
Not sure about the quality of the VFD because still trying to figure out how to get remote start to work. Seems to run the 7 hp 3 phase motor fine from 220 single phase. I would suggest...

Attached my guess at wiring diagram for remote stop start of Vevor vfd.

any suggestions welcome

Mike Schuch
I followed your suggestion, bought a 10 hp 7.5 kw vfd for the 7.5 hp main motor, and a smaller one for the 1.2 hp scoring. - Vevor VFD's - and they run the motors fine when started via...

An update: I bought a Vevor 10 hp VFD from Mr. B. to try on the main 7.5 hp 3p motor. Hooked it up to a 30 amp 220 v breaker and the motor and fiddled with the settings for about an hour and got it...

Thanks for all the input. Will look at the FUJI vfd's. I am not too concerned about doing the wiring - but have a friend who is an electrician if I stumble, or to look things over before I push...

Carl,
Send me a note if you try a VFD. I would like to go that route with my 7.5 hp 3p saw motor. The cost of the drives ranges from about $170 to $1800 - and I have no idea why the variation...

Thanks for all the responses.

Current single phase equipment includes a 350 mm Minimax J/P, Aggazani 5hp 600 mm bandsaw, and a Hammer sliding table shaper. 3 hp cyclone dc.

I will try to...

Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know
a) what specific vfd you are using if you recommend it,
b) any...

I am a relatively new owner of a 600 Aggazani - about a month now. Mine is a single phase 5 hp, which I was pleased to find as I do not have 3 phase power.
Mine came with a couple of 1 inch wide...

I found a 2003 manual, but am looking for something closer to 1996 if anyone has one.
Thanks,
Mike

Hugh,
Have you been happy with your scmi si 12? I have been looking at one, and would appreciate thoughts you have. I have a unisaw currently and like it. Hobby shop.
Thanks,
Mike

Jeff,
We got it set up and ran a 2x6 through it with a 32" gap to the Laguna fence, and it came off very uniformly. Out of the box.
I will get a 1/2" sometime, but the 1 inch Lennox carbide...

Thanks for all your feedback/advice.
I ended up taking off the table and the motor, leaving the wheels on, and then strapping a 6 ft long pallet I had made for moving it to the spine with several...

I am going to pickup a new to me 2008 Agazzani 600 bandsaw this weekend, and intend to put it on its back to transport. Am planning to remove the table and would also like to remove what I...