Search:

Thanks all. I sprayed the project and it looks good.

Well... that would be good. I guess I read so many things about finishes going bad I assumed this would too, thanks.

Anybody know how to read Deft date codes? I've searched the internet and have had no joy...

C26192/BE0461PM03:20
CC 1. 50

I thought I might have a bad rattle can 'cause it didn't rattle......

I have a Jet 1642 EVS-2 that I bought new around 2007 that has a mild vibration. I've removed the drive belt and the drive pulley and it still vibrates which tells me it's in the motor. The vibration...

Maybe too late... but Grizzly makes a drum extender.

https://www.grizzly.com/products/grizzly-collection-drum-extension-kit-for-g0440-g0443/t25506

Fixed... I think...

Broke a blade and it was pretty exciting!!:eek:
I'd been cutting some green Black Locust and just getting ready to start on the last log. I walked around the back of the saw while it was running and...

I bought the Portamate Pm-3500 for mine. It rolls on the long axis of the planer where the Hammer rolls on the short axis. Getting thru a doorway with the Hammer version might be tougher. That worked...

OK... problem solved. (I like threads that are resolved)

I'm sure you all have been waiting for the resolution... chuckle

I thought I was paying normally with my credit card since I don't have...

OK... this is strange... everyone agrees on option 1. I figured there'd be more discussion... HA!! But that makes it easy. If someone else has an opinion throw it on out. Mike, it's a MiniMax S400P...

I like the one below in my signature... Red Green... "Any tool can be the right tool"

If I remember correctly, the clip on his show showed him with a 2x4 in front of him with various types of...

A shiny new tool is going to show up in my shop next week!!!! W00 HOO!!! It requires a 240v 30a circuit that I don't have... but I do have a 50 amp circuit set up for a welder.

So...

Option 1...

Ralph, that would be the most likely problem. I tried yet again, being very careful, even had the GF check everything... still no go. So I called the bank, they looked up the transaction and told me...

Tried last night and today, same result... paying with a credit card... card denied. I called the bank to check and the card is good. Only thing I can see is the name on the card has middle initial...

I like the adjustment arrangement you have for leveling the outfeed table to the saw... I need to do that with mine. Can I borrow that idea??:)

Just being cautious, they seem like nice folks. I found them on Ebay but am dealing with them directly.

http://reardonmachinery.com/product-category/new/

Well shoot...

I thought this thread was going to be about messin' with the acoustics to make the music sound better in the shop after the work was done, you know, AFTER the power was shut off, and...

How about this...

http://s275.photobucket.com/user/teh_thorntonzor/media/squirreltrap.gif.html

Sounds like you've got your answer, but here's another way to look at it...

Let say your amp is putting out 8 volts at "whatever" frequency into an 8 ohm load, that's 8 watts of power at the load...

Mine planer is a 733... but here's what I did to connect it to my 6" system... and yea, it's noisy.


245872

I had the same injury a few years ago..... VERY scary.

I was cutting one of the last pieces for a shed I built.

That shed now has a name, and that name is on a sign mounted on the front of...

Anthony, The cyclone and muffler are in the garage, the shop is on the other side of the wall to the right. The muffler has a door inside that directs the exhaust outside if the weather is nice, or...

Yup... don't bother...

Err wait!!! I've got one that's hardly used!!! Wanna buy it?!?!?! Shipping to Australia can't be that much...

Now THIS is a muffler!!!!!!!!!!!!!! And it works really...

Ahh what the heck... I'll take 51

When I rewired my shop I got away with a 3 wire feed ONLY because I didn't replace the subpanel (grandfathered). A NEW subpanel would have required me to run a NEW separate ground wire. I got my...