Search:

Type: Posts; Posts From Last Day

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. The threads below have not been updated since your last visit or since forums have been marked read.
  2. I need the bottom half

    Started by lowell holmes, Today 4:11 PM
    • Replies: 1
    • Views: 0
    Last Post: Today 4:21 PM
    by Bill Houghton  Go to last post
  3. What to do with an old 8" jointer?

    Started by Zachary Hoyt, 10-16-2018 10:54 AM
    2 Pages
    1 2
    • Replies: 27
    • Views: 1,137
    Last Post: Today 4:16 PM
    by Andrew Hughes  Go to last post
  4. New Grizzly G0868 Jointer

    Started by Matt Przybylski, Today 11:58 AM
    • Replies: 6
    • Views: 125
    Last Post: Today 4:10 PM
    by Matt Przybylski  Go to last post
  5. spiraling or texturing tool

    Started by jeff oldham, 10-16-2018 11:05 PM
    • Replies: 10
    • Views: 403
    Last Post: Today 4:09 PM
    by John K Jordan  Go to last post
  6. Post Oak? Should I mill?

    Started by Audie Milner, 10-11-2018 3:40 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 416
    Last Post: Today 4:00 PM
    by John K Jordan  Go to last post
  7. Hammer slider fence stop.

    Started by C Scott McDonald, Today 1:25 AM
    • Replies: 2
    • Views: 119
    Last Post: Today 4:00 PM
    by Jay Runde  Go to last post
  8. Opinions wanted on Minimax MM16

    Started by Vinito Caleb, 03-22-2017 3:06 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 2,835
    Last Post: Today 3:53 PM
    by Jim Fuller  Go to last post
  9. Cleaning 2-ply acrylic

    Started by Steve Krahn, Today 3:48 PM
    • Replies: 0
    • Views: 1
    Last Post: Today 3:48 PM
    by Steve Krahn  Go to last post
  10. Why aren’t there many stainless steel body hand planes?

    Started by Bill Dindner, 10-17-2018 7:43 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 628
    Last Post: Today 3:38 PM
    by Van Huskey  Go to last post
  11. Wood business cards

    Started by Jamie Ringelberg, 10-17-2018 11:15 AM
    • Replies: 7
    • Views: 235
    Last Post: Today 3:32 PM
    by Paul Phillips  Go to last post
  12. Wood type for exterior door.

    Started by Jared Sankovich, 10-08-2018 8:52 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 789
    Last Post: Today 3:32 PM
    by Jared Sankovich  Go to last post
  13. Which bandsaw blades

    Started by Dean S Walker, Today 12:11 PM
    • Replies: 4
    • Views: 66
    Last Post: Today 3:32 PM
    by Wally Wenzel  Go to last post
  14. Thermal imaging camera

    Started by Kurt Swanson, Today 10:24 AM
    • Replies: 4
    • Views: 120
    Last Post: Today 3:29 PM
    by Jared Sankovich  Go to last post
  15. Garage Door Opener table lift

    Started by Gordon Stump, Today 3:29 PM
    • Replies: 0
    • Views: 6
    Last Post: Today 3:29 PM
    by Gordon Stump  Go to last post
  16. Hello again

    Started by Bob Warfield, 10-17-2018 6:49 PM
    2 Pages
    1 2
    • Replies: 22
    • Views: 679
    Last Post: Today 3:19 PM
    by Bruce Haugen  Go to last post
  17. Another Email For Which to Watch Out

    Started by Jim Koepke, 10-08-2018 1:53 PM
    • Replies: 7
    • Views: 509
    Last Post: Today 3:19 PM
    by Thomas L Carpenter  Go to last post
  18. Justifying A Major Tool Purchase

    Started by Julie Moriarty, 08-14-2018 11:47 AM
    46 Pages
    1 2 3 4 5 ... 46
    • Replies: 676
    • Views: 37,558
    Last Post: Today 3:15 PM
    by ChrisA Edwards  Go to last post
  19. Baldor grinder

    Started by MICHAEL YASKO, Today 2:17 PM
    • Replies: 2
    • Views: 35
    Last Post: Today 3:05 PM
    by Kyle Iwamoto  Go to last post
  20. Balsa wood

    Started by Pat Shirkey, Yesterday 10:02 AM
    • Replies: 4
    • Views: 156
    Last Post: Today 2:58 PM
    by Pat Shirkey  Go to last post
  21. A new use for parallel clamps

    Started by Matt Day, Yesterday 10:30 PM
    • Replies: 4
    • Views: 204
    Last Post: Today 2:56 PM
    by Jim Koepke  Go to last post
  22. Hot in the Shop!

    Started by Dave Richards, 10-17-2018 7:23 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 442
    Last Post: Today 2:54 PM
    by Van Huskey  Go to last post

    Forum:
    WorkShops

  23. Local Expressions / coloquialisms

    Started by Malcolm Schweizer, 10-17-2018 10:08 AM
    5 Pages
    1 2 3 4 5
    • Replies: 68
    • Views: 1,103
    Last Post: Today 2:44 PM
    by Jim Koepke  Go to last post
  24. Acorn controller Changes Coming?

    Started by Bill George, Today 8:05 AM
    • Replies: 5
    • Views: 70
    Last Post: Today 2:21 PM
    by richard newman  Go to last post

    Forum:
    CNC Machines

    • Replies: 0
    • Views: 15
    Last Post: Today 2:15 PM
    by daniel coyle  Go to last post
  25. Oneway Chuck Spur

    Started by MICHAEL YASKO, 10-16-2018 8:59 PM
    • Replies: 8
    • Views: 257
    Last Post: Today 2:13 PM
    by MICHAEL YASKO  Go to last post
Results 1 to 25 of 79
Page 1 of 4 1 2 3 4