Search:

Type: Posts; User: Eugene Dixon; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    601

    Congrats Jim on the permit. I was hanging DC...

    Congrats Jim on the permit.
    I was hanging DC duct last week. Realized yesterday that I made a mistake and not have to rearrange two branches. Moral of the story, check your design document.
  2. Replies
    12
    Views
    686

    Finished dust collection closet by installing LED...

    Finished dust collection closet by installing LED strip lighting on the two long walls mounted to flat boards at 45 degrees as "crown" molding. Spent time on the motor starter wiring to get the run...
  3. Replies
    43
    Views
    3,875

    Felder called Friday and left a message. They...

    Felder called Friday and left a message. They called again today. Not a lot of technical help and everything I might want has to come from Austria or has to be fab'd in Austria.

    Rep indicated...
  4. Finished the DC closet and installed lights. ...

    Finished the DC closet and installed lights. Need to wire up the MS, etc. Waiting for the piping.
  5. Replies
    43
    Views
    3,875

    PM sent. Here are more characters to meet the...

    PM sent.

    Here are more characters to meet the limit.
  6. Ordered DC duct. Continued work on the closet. ...

    Ordered DC duct. Continued work on the closet. Worked on a few small pieces in prep for building a high vise.
  7. Replies
    43
    Views
    3,875

    Never saw a machinist detension a bandsaw blade...

    Never saw a machinist detension a bandsaw blade during my career in equipment development in private industry, either. Just a habit I have gotten into for woodworking.
  8. Replies
    5
    Views
    1,292

    Ditto what Don said.

    Ditto what Don said.
  9. Replies
    43
    Views
    3,875

    Faithfully de-tension after each use, Mike. the...

    Faithfully de-tension after each use, Mike. the encouragement and the insight is appreciated.
  10. Replies
    10
    Views
    1,408

    I use 1" glass sample bottles for my light...

    I use 1" glass sample bottles for my light houses. I cut them to length with a 10" HF wet saw using a diamond blade then square the ends with 220 sanding papers. The saw and blade are left overs...
  11. Replies
    23
    Views
    2,456

    It takes a lot of sweeping compound to clean up...

    It takes a lot of sweeping compound to clean up joint compound dust.
  12. Focused on the DC closet all week. Finished the...

    Focused on the DC closet all week. Finished the exterior this evening except for final mudding.
  13. Replies
    43
    Views
    3,875

    I'm behind in updating this thread. I installed...

    I'm behind in updating this thread. I installed the urethane tires using a jig (video) from the supplier. The jig made it easy. Basically to 1/2" dowels one is the axis for the wheel and the other...
  14. Replies
    43
    Views
    3,875

    Where's the Hammer/Felder Service Department for...

    Where's the Hammer/Felder Service Department for the NE? I've called several times. Emailed multiple times. Even had the sales rep contact me for intervention but no response for Support or...
  15. Replies
    202
    Views
    18,343

    Planning on installing one of those on the house...

    Planning on installing one of those on the house garage as soon as I can get the shaft above the door. Replacing a Wayne Dalton system which doesn't not work well with summer temperatures.
  16. Replies
    41
    Views
    4,611

    And the Flamenco dancers at the Columbia. ...

    And the Flamenco dancers at the Columbia. Planning another visit in October.
  17. Turned several green cherry bowls. Road trip to...

    Turned several green cherry bowls. Road trip to retrieve a flammable storage cabinet purchased to store tractor and generator fuel and got it set up. Purchased some materials for the DC closet...
  18. Replies
    43
    Views
    3,875

    Thank you Ted.

    Thank you Ted.
  19. Replies
    43
    Views
    3,875

    Update 3/24 Yesterday, I spent a couple of hours...

    Update 3/24
    Yesterday, I spent a couple of hours cleaning glue from the wheels. Scrapping with a razor blade was slow. I found that soaking a rag in acetone and just rubbing the wheel was more...
  20. Replies
    43
    Views
    3,875

    Mark, Very interesting. Thanks

    Mark,
    Very interesting.
    Thanks
  21. Finally, assembled the frame and stood up the DC...

    Finally, assembled the frame and stood up the DC onto the frame. Now to surround with noise suppression, add electrical, and ducting. Needing that tax return. Also visited the Savannah River...
  22. Replies
    43
    Views
    3,875

    @Rod, will do. Need to make, borrow, or buy a...

    @Rod, will do. Need to make, borrow, or buy a tensionometer. Trying to put all my energy and resources into dust collection right now.
    @Tom, not clear what you mean by this, "Curious to see how...
  23. Replies
    43
    Views
    3,875

    Thank you for all of the thoughts. For those...

    Thank you for all of the thoughts. For those asking/pondering, I've always bought tires from Felder/Hammer in Delaware. These have always been rubber tires. I have not added heat prior to...
  24. Replies
    43
    Views
    3,875

    Bandsaw Threw a Tire, Again

    I've had a Hammer N4400 for a few years. Each year it seems I have to replace the tires. I threw the tire off the lower wheel today after running the saw for a couple of hours prepping bowl blanks....
  25. Replies
    8
    Views
    1,258

    Either Doug Thompson or Oneway has a video...

    Either Doug Thompson or Oneway has a video covering exactly what David described -- in case you are a visual learner.
Results 1 to 25 of 361
Page 1 of 15 1 2 3 4