Search:

I am after a cheaper price.

These hobby suppliers are clearly having someone cut this material for them and repackaging it so there is no way they are going to provide that kind of info. I am not...

I am buying many packs of material like this consistently
I don't need it to be 2 ft lengths - it could be 8ft +...

I have tried calling several places locally to supply material like this but no...

having issues with the glue joint strength. I have maybe a 75% success rate with the joints. I would expect it to be 100%...

I have found that, despite what most people say, that using a ton of...

I have been mixing resins by hand, usually with a random 1/2" x 1/2" x 12" piece or something close to this that is sitting around the shop. I am mixing roughly 1k ml at a time - not a ton, but I do...

Brian, I have seen the mud jacking/slab jacking companies. Problem is, my area is finished with the bottom plate of walls tap-conned to the floor. If it were jacked, it would push the ceiling up.
...

The concrete floor sank, probably decades ago from poor prep. Has since been stable. Was poured 30+ years ago

There is no heaving as it has rebar. It is not painted and the surface is in great...

I need a setup for CA glue that has a very thin tip for accurate placement of glue and less oozing all over the small stuff I am building.

I know there are small bottles with fine metal tips, but...

I need something like construction adhesive that I can fill small jars with, seal the jars, and not have the adhesive cure while in the container.

Doesn't need to be construction adhesive, but...

thanks everyone. Another point I did not mention, I have found at Lowes that when I purchased the highest grade 2x4x8's, they were very red and did not stain consistently. However, the 2x4x10's are...

I need to buy quartersawn fir. I am currently buying roughly 30-40 2x4x10's per month from lowes, but picking through their selection for quartersawn or 'close to quartersawn' is very time consuming....

At this point I am doing enough production work of weathered pieces to justify a machine. I am looking at the 19-38 combo machine (strictly for the metal wire wheel abilities) but have reservations...

I don't know yet, but ideally something that is water based (low odor since it is in the basement) and sprayable. Polycrylic?

I need to put a finish on hundreds of boards (28"x4"x.5") and will have to do it on a monthly basis.

I was thinking of taking 2ft x 2ft pieces of thin plywood and using many thin through it so...

Hi Peter, I don't know what direction it is intended to flow. I did not see a spec on the website.

I actually only paid around $60 for the filter on ebay.

Hi Art,

When I blow the cartridge out, I remove it from the dust collector setup and blow it out outside. I blow from the outside in and do this over the entire pleated surface until no more dust...

Hello everyone,

I bought this cartridge filter below off ebay in new condition just over a year ago:
...

I know this thread is not related to sublimation printing, but I believe many of the laser engraver folks are well acquainted with the process.

I am in Rochester, NY. Looking to experiment with...

OK. I just got off the phone with a lady at WD Lockwood and she said that I MUST use a clear coat of some kind over the wood after the dye stain goes on, or else the stain will come off if it is...

Thanks, Doug. Have you found the color charts to be accurate? The wood I am using is resawn 2x4's, so I believe it is Hemlock - very light color.

Do you think that using the bath process like I am...

Thanks guys. I will look into the dyes. One thing I do like about the current solution I use is that it gives a contrast of color - like in the areas where the wire wheel removes the grain, the color...

Thanks, Glenn

I don't know what more I can do time-wise - as soon as the solution is ready I do a test piece in the morning, let it dry for 2 hours (fully dry is the only way to tell what it...

I manufacture a few items that I use this finish with, so the number of pieces to do is usually 200+. I made a dipping tank since it is faster and more consistent than paining the solution on.

I'm...

Hi Scott,

I have this saw. I actually took the scoring blade assembly off since I never used it. Without the scoring blade the saw can run a 12" blade which I find much more usable than a scoring...

I did. They did a bank check and allowed it to clear 14 days. Both theirs and my bank stated that after it was cashed there was no way to put a stop on the funds but the 14 days could be taken as an...

funny you mention billiard table, as this is the very reason I bought the machinist's level. I was able to shim a 1917 full size brunswick to less than .003" on the entire playing surface. 1" slate....