Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.30 seconds.

  1. For HVAC work he will need an accurate platform...

    For HVAC work he will need an accurate platform scale for weighing in refrigerant. Make sure it is battery powered. I bought mine used for around $70. New they cost about $200 or more. Must be...
  2. Replies
    7
    Views
    136

    Harbor freight sells an O-ring assortment in a...

    Harbor freight sells an O-ring assortment in a plastic divider case for under $10. If it fits that is probbably cheaper then ordering one. That is how I bough the metric woodruff key I needed for...
  3. My brother made a walnut and Acacia kitchen...

    My brother made a walnut and Acacia kitchen table. Light color marble slabs for the top to take any abuse. It looks good against a room full of oak floors. These are the oak floors from the 50's....
  4. Replies
    7
    Views
    136

    Measure the diameter of the cord then the inner...

    Measure the diameter of the cord then the inner and outer diameter. It could be metric or English units, where was it made? Are you sure it is just a o-ring and not a seal or a square ring seal....
  5. Replies
    2
    Views
    102

    If that is the table saw it is a c-mount motor. ...

    If that is the table saw it is a c-mount motor. You may have to remove the pulley first. I would cut the power cord as close to the motor as possible. Add a short pigtail cord at the bench. Ad a...
  6. Replies
    6
    Views
    231

    Anti fog spray for glasses with mask

    With having to wear a mask almost all the time outside I would like to find a better antifog spray for my eyeglasses. I used to get it at walgrens or CVS. They dropped the antifog part and raised...
  7. General Metalworking For $10 or under the harbor freight ones are...

    For $10 or under the harbor freight ones are okay. I would not run them continuous more then 10 minutes
    betweeen cooldowns.
    Bil lD
  8. cross bow or radio controlled car to get the...

    cross bow or radio controlled car to get the string from the access hatch to the drop site. They make special cross bows for fishermen that already have the line reel attached. I believe Klien?...
  9. Replace it the metal is stretched and will never...

    Replace it the metal is stretched and will never go back to flat without using a metal shrinker . I do not think a shrinker will work on stuff that thick, they are designed for car sheet metal. The...
  10. Replies
    9
    Views
    394

    A week later, no response, so. ... rent a...

    A week later, no response, so. ... rent a jackhammer and cut a channel in the rock wall install some conduit for the cable and slap some concrete over it to hide the slot. I have to assume he lives...
  11. On my 12/14 I threw away the plinth and mounted...

    On my 12/14 I threw away the plinth and mounted it up on a mobile base with big wheels. I put a piece of plywood under it to seal the base for dust collection.
    I moved the dust chute, at the...
  12. The top of the slot is one inch wide. A 1 2 3...

    The top of the slot is one inch wide. A 1 2 3 block sits perfectly in the slot to help align the fence to the slot. Do you have the correct mitre gauge? The way I did it was to clamp a 2x4 to the...
  13. Replies
    53
    Views
    2,059

    That is the reason big clock tower clocks run a...

    That is the reason big clock tower clocks run a fraction slow, never fast.
    Bil lD
  14. Replies
    16
    Views
    404

    Older electric stoves and dryers used the ground...

    Older electric stoves and dryers used the ground as neutral for 120 volt lights etc. Now they are required to have a neutral wire if they use 120. I bet any 240 volt washing machine shad to carry a...
  15. Replies
    466
    Views
    29,629

    social distancing plane and spacecraft like I...

    social distancing plane and spacecraft like I expected to see.
    The Mustang is a F82 or P82 that was actually flown.
    Bill D.

    The nuclear powered bomber does not look that different from a B52.
  16. The crush tube rotates with the inner races. On...

    The crush tube rotates with the inner races. On a unisaw the flange end bearing is locked in place the other end is free to float in the bore. Is the new flange end bearing the same thickness as...
  17. Replies
    17
    Views
    563

    He probably thinks rotary cut is the cheapest...

    He probably thinks rotary cut is the cheapest walnut veneer he can get. Give him prices for flat sawn, solid and rotary cut. For most woods rotary cut is the cheapest veneer so he probably thinks...
  18. Replies
    25
    Views
    906

    The sanding head contactor is using L1 and L3. ...

    The sanding head contactor is using L1 and L3. The other two contactors are using L1 and L2. The forth terminal on the right side of the contactors is a low power switch, it may be low voltage as...
  19. Replies
    25
    Views
    906

    The contactor switches and the overloads are...

    The contactor switches and the overloads are bypassed. Power should come in to L1 then out to T1, L2 to T2, and L3 to T3 when it is pulled in. They do not use one contact number since there are...
  20. Replies
    8
    Views
    375

    fixed that. I liked the one where they used...

    fixed that. I liked the one where they used tungsten plates in the middle of the bricks. I saw on TV where ancient forgers used platinum slugs and riveted on gold covers. Today the platinum is...
  21. Replies
    3
    Views
    144

    Be careful and do not break the table trunnions. ...

    Be careful and do not break the table trunnions. 600 pounds seems reasonable for a 20" DP. Have shipper lower table all the way or take it off. then lower head to the base as well.
    Bill D

    this...
  22. Replies
    25
    Views
    906

    With fuse #2 pulled it is not the control wiring....

    With fuse #2 pulled it is not the control wiring. You say the armatures do not suck in under power on any contactor? This means either the contacts are welded shut or the power wires are connected...
  23. Replies
    8
    Views
    375

    Maybe the scammer can be paid with the gold...

    Maybe the scammer can be paid with the gold plated Chinese brass ingots.
    I am not sure if this can be called a scam since I assume the government in China knew what was happening. The insurance...
  24. Replies
    6
    Views
    374

    Where does the unisaw come into this decision?

    Where does the unisaw come into this decision?
  25. Replies
    28
    Views
    862

    Sounds like it has bronze bushings not ball...

    Sounds like it has bronze bushings not ball bearings. I would dump it for that reason alone.
    Bill D
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4