Search:

Type: Posts; User: Eugene Dixon; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    62
    Views
    3,627

    Been thinking the last 2 days that I was missing...

    Been thinking the last 2 days that I was missing The Hall. Thank you for the updates. Here's hoping your roof stays tight and the chimney leaks never more.
  2. Replies
    56
    Views
    3,492

    Got a note from Grizzly today. Clamps on sale. ...

    Got a note from Grizzly today. Clamps on sale. YMMV.
  3. I went to AgriSupply and got an 1-1/2" wrench to...

    I went to AgriSupply and got an 1-1/2" wrench to remove chucks with inserts. Cost <$12. Spent a little time thinning it so that it would get between the chuck and the spindle flange. Should also...
  4. Replies
    12
    Views
    496

    Mr. Balolia, Thanks for sharing the video. ...

    Mr. Balolia,

    Thanks for sharing the video. Thanks for sponsoring the SMC.
  5. Finished a 15" NE pecan bowl with bowties. Had...

    Finished a 15" NE pecan bowl with bowties. Had to stop shaping the exterior when I started finding deeply embedded pieces of metal. Bowl has a natural split (max ~1/2" wide" with bark inclusions...
  6. Replies
    4
    Views
    534

    Thanks for the 'turn' John. No truckload. ...

    Thanks for the 'turn' John.

    No truckload. Most of what I have (had) is essentially found-on-the-side-of-the-road. Some from Raleigh, NC. Some from Nashville, TN. Some from down the road in...
  7. Replies
    4
    Views
    534

    It's two pieces...

    Spalted maple. Turn your head to the left as I can't get it rotated.

    432846

    432880

    No finish applied, yet. Suggestions?

    OBTW, the funky marks around the top are residue from the rubber...
  8. Replies
    18
    Views
    1,212

    Compression socks and stall mats have helped me...

    Compression socks and stall mats have helped me with foot and leg aches.
  9. You might suggest that your young friend watch a...

    You might suggest that your young friend watch a Rob Cosman video on sharpening.
  10. Take some measurements. Explore McMaster Carr. ...

    Take some measurements. Explore McMaster Carr. They will have machined washers. If you look at their saw blades and accessories, you might get lucky and find some machined flanges/stabilizers
  11. Replies
    5
    Views
    605

    Very nice, for sure.

    Very nice, for sure.
  12. Replies
    22
    Views
    995

    Hope you meant 1/2". When I toured the lumber...

    Hope you meant 1/2". When I toured the lumber mill they were using 8"-12" bandsaw blades, however.
  13. Replies
    13
    Views
    489

    Made a couple of funnels (bad week), turned a...

    Made a couple of funnels (bad week), turned a couple of bowls, split some maple with the Husqvarna, cut down neighbor's dead Bradford pear and harvested some nice pieces for bowl blanks, cut the...
  14. You might check with Jamestown Distributors and...

    You might check with Jamestown Distributors and get their thoughts.
  15. Replies
    60
    Views
    3,771

    Run it through the still again!:D

    Run it through the still again!:D
  16. Replies
    17
    Views
    1,517

    Spent Saturday morning with the chainsaw. Spent...

    Spent Saturday morning with the chainsaw. Spent Saturday afternoon with the recliner.
  17. Replies
    12
    Views
    1,013

    Penguin & Fish, according to dearly beloved, has...

    Penguin & Fish, according to dearly beloved, has a pattern. This is a quilters site. Dearly Beloved made a couple of masks yesterday and plans to make more for a nursing friend.
    ...
  18. Replies
    11
    Views
    540

    Is your rip fence straight/flat down it's length?

    Is your rip fence straight/flat down it's length?
  19. Looks like an opportunity to make two doors from...

    Looks like an opportunity to make two doors from one door with pre-fitted hinges.
  20. Replies
    36
    Views
    1,800

    And, I just put an old towel over the tables....

    And, I just put an old towel over the tables. Occasionally I'll add the floor wax.
  21. Replies
    14
    Views
    732

    Depending on how much torque you tend to apply,...

    Depending on how much torque you tend to apply, could you possibly fill the damaged holes with epoxy and bore out appropriately?
  22. Replies
    37
    Views
    2,627

    Be nice to get a dimensioned sketch of his inside...

    Be nice to get a dimensioned sketch of his inside tool rest. I've tried to contact him via the Dallas Woodturning club but got no reply from the club.
  23. For off center holes, check the OneWay device.

    For off center holes, check the OneWay device.
  24. FWIW, I have successfully negotiated by phone...

    FWIW, I have successfully negotiated by phone with Woodcraft corporate for a discounted bulk order in the past. YMMV
  25. Replies
    5
    Views
    500

    What is 'near'? Check the AAW.

    What is 'near'? Check the AAW.
Results 1 to 25 of 218
Page 1 of 9 1 2 3 4