Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. It is designed to be a chain lube so it should...

    It is designed to be a chain lube so it should work fine.
    I think waxing the chain is a hold over of mis translating British English. In the early days British soaked their chains in paraffin to...
  2. AFAIK It has teflon not silicone so no finishing...

    AFAIK It has teflon not silicone so no finishing problems. I did not notice any smell. Drys fast when it is 95 in the shop.
    Bill D
  3. Replies
    9
    Views
    295

    https://www.etrailer.com/faq-Adding-Electric-Over-...

    https://www.etrailer.com/faq-Adding-Electric-Over-Hydraulic-Disc-Brakes.aspx

    https://www.easternmarine.com/electric-hydraulic-brake-actuators
  4. Echo and Tanaka make gasoline powered drills....

    Echo and Tanaka make gasoline powered drills.
    Bill D
  5. One of the first Tesla battery fires happened...

    One of the first Tesla battery fires happened while a guy was driving on the freeway. The fire department took hours to get it stopped. Tesla gave him a free new one so they could examine then old...
  6. Replies
    12
    Views
    729

    Since the new ring will not be a perfect match...

    Since the new ring will not be a perfect match make it a contrasting wood or even brass. Walnut and ebony come to mind.
    Some would make the edge a river table or is that outdated yet?
    Bill D
    Bill...
  7. Dupont chain saver lube. My new dry lube

    I mentioned it in my jointer thread and thought I would post a new thread about Dupont Chain Saver spray lube. It goes on wet about like wd40 but in a few minutes it dries to a thin teflon wax film....
  8. Replies
    6
    Views
    501

    I understand that 1/1000 of an inch is the...

    I understand that 1/1000 of an inch is the minimum the human eye can see as no being the same. So you are plenty close enough. I have read 0.003 is fine.
    Bill D
  9. Replies
    20
    Views
    686

    Outlets mounted horizontally have to be with the...

    Outlets mounted horizontally have to be with the ground to the left. This means Neutral is in top. Same safety reason as ground should be on top of a vertical outlet.
    Bill D
  10. I thought it was a proof of concept joke to have...

    I thought it was a proof of concept joke to have pantograph equipped electric trucks. Turns out it is real for off road mine trucks.If caterpillar is selling them today it is no joke. Of course...
  11. The picture looks like a standard socket at each...

    The picture looks like a standard socket at each end. I think they are all the same 10mm size ball. Not really a critical fit at such low speeds.
    looks like 8, 10, 13 and 16mm are commonly used....
  12. I do not think that is a hydraulic cylinder. It...

    I do not think that is a hydraulic cylinder. It looks like a gas strut . You need to disconenct it and use a scale to lift up on whatever weight drops down. That force, or more, is how much the...
  13. Replies
    15
    Views
    647

    I am 6'2" tall so I normally like to raise my...

    I am 6'2" tall so I normally like to raise my tools a few inches on a mobile base. I also like to leave some toe room under the base.
    Bill D
  14. Replies
    6
    Views
    526

    Thanks for posting Here is a 1873 water powered...

    Thanks for posting
    Here is a 1873 water powered foundry and shop. The foundry shut down around 2000 because of smog laws. I think it is a museum now. It had a water turbine running the tablesaw...
  15. Replies
    44
    Views
    1,486

    The radiation thing is for emitted radiation when...

    The radiation thing is for emitted radiation when in use. It is not emitting when it is in your pocket, it is only receiving em waves then.
    Bill D
  16. Replies
    12
    Views
    729

    I priced a book matched elm burl veneer for my...

    I priced a book matched elm burl veneer for my 5" diameter table and repaired what I have. Over $400 for the wood. It would be cheaper to buy an antique in good condition and refinish it as...
  17. cleaning segmented infeed rollers on a planer

    My Powermatic planer has a segmented infeed roller. All I can find online is how to clean a rubber covered roller. It has some pitch and what not embedded into the teeth. I assume a wire brush and...
  18. Replies
    6
    Views
    487

    You do not set the blades at 90. You set them so...

    You do not set the blades at 90. You set them so the knife edge is as high as it can be. You need to level the tables to the blade height before removing them. Sounds to me like your blades are...
  19. Replies
    44
    Views
    1,486

    Watch out for free upgrades. We had to go to 4g...

    Watch out for free upgrades. We had to go to 4g and Verizon offered to give us free phones that would work. They were free because we were long time customers.
    Problem was if you took the "free"...
  20. Replies
    3
    Views
    295

    I should have said weathertech is cut to fit. ...

    I should have said weathertech is cut to fit. Husky says they have made to fit.
    Bill D
  21. I got the dovetails cleaned up without table...

    I got the dovetails cleaned up without table removal. In was able to pull the gibs then get some tools in to clean them out. The outfeed table was the worst I kept getting fine grit on a pipe...
  22. Replies
    3
    Views
    295

    Floor mats for my Ford Ranger, 2000

    I need to get some new floor mats for my 2000 ford ranger. I want heavy rubber no carpet or leather. No one seems to make ones that custom fit. If I have to cut to fit anyway I do not see the...
  23. Replies
    6
    Views
    480

    Do not overclean the coils. Coils transfer more...

    Do not overclean the coils. Coils transfer more heat if they are slightly rough. factory new clean and polished get better as a light dust film forms and causes turbrulance in the air flow.
    Bill D
  24. Replies
    32
    Views
    4,162

    I will jump in here without having read all the...

    I will jump in here without having read all the previous posts. I think for most people you do not really care too much about the actual flow rates and pressures. You are simply trying to get max...
  25. Replies
    13
    Views
    881

    Politically correct term for Nipple Extractor....

    Politically correct term for Nipple Extractor.
    Bill D
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4