Search:

Type: Posts; User: Jim Koepke; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.21 seconds.

  1. Replies
    39
    Views
    1,053

    Into the 1950s and '60s most men dressed well,...

    Into the 1950s and '60s most men dressed well, wore ties and hats to work even for non-office jobs. It has gotten much less formal since.

    jtk
  2. Replies
    752
    Views
    56,033

    Too short? It only takes ten and they can be...

    Too short?

    It only takes ten and they can be spaces.

    jtk
  3. Replies
    27
    Views
    680

    The package was in today's mail. It didn't...

    The package was in today's mail.

    It didn't look like it drank all the liquor in Puerto Rico. Maybe that was Costa Rica. Well, it ain't nobody's business but my own…

    jtk
  4. Replies
    39
    Views
    1,053

    There is an old story told about a woman who had...

    There is an old story told about a woman who had two sons. One went off to sea the other became Vice President. She didn't hear anything about either of them after that.

    jtk
  5. Replies
    15
    Views
    5,636

    Howdy Barry and welcome to the Creek. By any...

    Howdy Barry and welcome to the Creek.

    By any chance did you notice this thread is over a decade old?

    jtk
  6. Replies
    16
    Views
    571

    Dowels are always good for hand tool work. One of...

    Dowels are always good for hand tool work. One of these makes it easy:

    443662


    Making a tongue and groove might be easier.

    jtk
  7. Replies
    27
    Views
    680

    That may have taken place when the Postal Service...

    That may have taken place when the Postal Service was separated from being subsidiary of the government. As a department of the government they could be compelled to post official government...
  8. One of my employers was notorious for being slow...

    One of my employers was notorious for being slow in paying their bills. One day on the way to work to purchase some tools the clerk noticed my uniform with my employer's emblems. He was going to give...
  9. Replies
    27
    Views
    680

    Day Six

    Maybe my package was placed on a direct flight from Puerto Rico to Portland, Oregon in a Piper Cub?

    443652

    Hopefully it will show up today.

    jtk
  10. Replies
    27
    Views
    680

    There are more accountants on the federal payroll...

    There are more accountants on the federal payroll scrutinizing the USPS than are looking over your shoulder.

    jtk
  11. Replies
    1
    Views
    211

    That looks great. The toe screw for the tote...

    That looks great. The toe screw for the tote looks like it was hand forged. One of mine was made by filing down a binding head frog screw to have a round head.

    jtk
  12. Replies
    39
    Views
    1,053

    Easy and already answered. What many do not...

    Easy and already answered.

    What many do not realise is we have had one President who was born a King.

    Some likely know the answer.

    jtk
  13. Thread: How to?

    by Jim Koepke
    Replies
    13
    Views
    468

    Cut across the grain first. This becomes the stop...

    Cut across the grain first. This becomes the stop cut when cutting with the grain.

    Some like to drill out the waste and do the clean up and squaring with chisels.

    The mortise was cut through...
  14. Replies
    16
    Views
    571

    That sounds like the traditional construction of...

    That sounds like the traditional construction of case work.

    Then there is at least a dozen ways to make the panels.

    jtk
  15. Thread: How to?

    by Jim Koepke
    Replies
    13
    Views
    468

    Here is how some of my corner joints were done...

    Here is how some of my corner joints were done years ago:

    443632

    One was a large cabinet the other was an animal cage. Both are still holding together. The tenon can even have some draw bore...
  16. If it does what you want it to do it is not...

    If it does what you want it to do it is not garbage.



    This is an important point for people buying a lot of used tools.

    Otherwise there is good reason for not letting a tool get so dull as...
  17. Replies
    16
    Views
    571

    In a lot of case work the backs were often thin...

    In a lot of case work the backs were often thin pieces ship lapped without being glued to allow for expansion during changes of weather.

    If you do use finish nails you may want to try "blind...
  18. Replies
    13
    Views
    757

    Boxes do tend to have similar yet traditional...

    Boxes do tend to have similar yet traditional qualities and appearances. Though my lid will be a solid piece. My scrap for the panels wasn't large enough to make bottoms for the two tills and a top....
  19. Replies
    13
    Views
    757

    Thanks for the kind words Kevin. My main...

    Thanks for the kind words Kevin.

    My main reason for choosing to use socket chisels many years ago was for the ease of making new handles. My lathe is a Craftsman lathe, made by King Seely, most...
  20. My dad didn't think so. His old '64 Chevy truck...

    My dad didn't think so. His old '64 Chevy truck had a wood deck. My recollection is he replaced it once and the second time it went bad he had a steel plate installed instead. It was used for a...
  21. Replies
    7
    Views
    625

    This reminded me of an acquaintance/friend in...

    This reminded me of an acquaintance/friend in Berkeley, CA who was a maker of pottery. He made many sizes and shapes. He also made a lot of small items less than an inch tall. He had a license to set...
  22. Thread: How to?

    by Jim Koepke
    Replies
    13
    Views
    468

    Do you have any way to create an image? It may...

    Do you have any way to create an image?

    It may be the late hour and one small glass of rum but the vision isn't coming to me.

    jtk
  23. Replies
    13
    Views
    757

    The glue up for this seemed as if it was going to...

    The glue up for this seemed as if it was going to be an ordeal. Then it dawned on me to dry assemble one side of the box while holding it in the vise to glue up the other side. Then it could be...
  24. Thread: How to?

    by Jim Koepke
    Replies
    13
    Views
    468

    Having an image of this would help a lot. Just...

    Having an image of this would help a lot. Just spitballing, can the styles on the width be mortised in above or below the styles for the depth?

    You could also settle for stringers between the...
  25. Replies
    31
    Views
    1,479

    Sounds good Doug looking forward to how this...

    Sounds good Doug looking forward to how this turns out. BTW, Welcome to the creek.

    jtk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4