Hello all. Hoping to get some feedback ideas on my Felder K3. I mainly cut 1/4" MDF pieces that are 48" L and 16" W. My crosscut fence in near perfectly aligned. I use the rip fence as a stop block...
Type: Posts; User: Joseph Mazey; Keyword(s):
Hello all. Hoping to get some feedback ideas on my Felder K3. I mainly cut 1/4" MDF pieces that are 48" L and 16" W. My crosscut fence in near perfectly aligned. I use the rip fence as a stop block...
Think I have finally got alignment in order. Believe the biggest issue was the rip fence. Even though being used as a stop block, it was creating enough of an angle that my pieces were coming out...
Thank you for the feedback. The one thing I am noticing is the rip fence is straight, but when I lock it the back tilts in towards the blade. I don't know if they is an issue that can be ignored as I...
Reaching out to people who may own a Felder K3 Hammer to get recommendations on alignment. When I got my K3 is was partially disassembled and I assembled it. From day one it has not been in alignment...
I have a digital readout on the rip fence side. That I ordered from Proscale. They did not make it for the K3 but going back and forth with an engineer on measurements and pictures, they were able to...
Curently own a Felder K3 Hammer and wondering if anyone has run across a digital reader for the cross cut bar. I know Felder makes one but at $1200 that is pretty pricey. Just seeing if there may be...
Just looking for opinions/feedback.
I have a 22x38 barn built on a pre-poured mono slab. Construction uses 6x6 posts. Exterior has been bubble wrapped and sheet metal. There are 2 - 2x6 supports...
@Aaron Inami - that makes sense. The first option sounds painful with a cut/adjust cycle. Thank you for the breakdown.
@Robyn Horton - thank you for confirming. That at least allows me the control...
Want to add one more comment to this as I have not got the straightest of answer from Felder. They are telling me the scoring blade is a little thicker than the main blade. The issue I have with that...
I have tried to weigh the idea of need as well. My grizzly cost me $1100. It has done worked but the fence is garbage. Theovehead dust was awful and replaced that right away with a shark guard. I do...
I did get a quote back on the Minimax and price was good. The biggest issue with them is their lead time currently is mid-Oct. Felder had one coming in at the end of this month. Laguna not sure...
I imagine the sliding table saw topics have been seriously beaten up on here. I am after more of am i comparing apples to apples here. Have an online business. Currently have a Grizzy hybrid cabinet...
I am going to switch hoses and see if that nets a better result. The 4 layer I have is only a inside foil layer and a black putter layer so unless 4 layer means something different to Infinity not a...
Kev,
Like the setup. Protect the units, muffle sound and don't have to worry about the weather beating up the box.
For my setup I have very limited space. My laser pretty much sets about 2...
Steve, follow up question for you. I got the 6" Infinity and also ordered their black hose. It says 4 layer but what I got looks thinner than the flexible stuff I can buy at HD. Not sure if I got the...
I am coming off a eBay laser using Lightburn and moving to Corel with Trotec. My main question is with the eBay laser I was use to a 0,0 axis and setting things in the laser at that point. With Corel...
Have not seen a lot around this topic on here. I have purchased a Trotec Speedy 100 still awaiting shipping. The stand for that unit runs around $595. Just wondering if anyone has gone with the stand...
Steve, are you using a 4" or a 6" model? The 4" looks to have 205 CFM where the 6" is double that.
So from what I heard the Mini 24 is gone and being replaced by one called Fusion Edge (believe that was the name). Speed is supposed to be 120 in/sec compared to 80 in/sec prior. Air Assist is still...
Was wondering if anyone had recommendations on an online exhaust for a Trotec Speedy 100. Want to avoid the HF dust collector as owned that prior and what something a little quieter. I am venting out...
For anyone that owns a Trotec Speedy 100 60w, what is the thickness that could be cut in wood? I would like to be able to cut 1/4" MDF and maybe some other woods like Alder and Cherry. I plan on not...
Recently spoke to a sales person and they could not give me a lot of information but had mentioned that Epilog was releasing a new version of the Mini 24 in the next 2-3 weeks. I believe the Helix is...
I have read different posts/comments about attending trade shows and getting better deals on lasers. Under the current circumstances not sure there are any shows happening but would it make sense to...
I currently use Lightburn on my eBay laser and have liked the ease of use and have a lot of templates designed in it. That said, I believe the developers of that software mentioned the higher ends...
Thank you for the feedback Kev.
I looked at the wattages a little more and also spoke to a Trotec sales rep this morning. I am looking at both 60 watt on the Trotec Speedy 100 and Epilog Mini 24....