The last time I had finish carpeters do custom mill work for me, they charged $100/hr. Considering most of the time required to make this piece is setup, the $130 sounds like it could be right. If...
Type: Posts; User: Frank Lopez; Keyword(s):
The last time I had finish carpeters do custom mill work for me, they charged $100/hr. Considering most of the time required to make this piece is setup, the $130 sounds like it could be right. If...
What is the difference between phelonic and solid countertop surface materials like corian? I would think you could pick up sink cut outs for next to nothing. Most are throw in the trash.
Now you got my little pea brain buzzing. Here's a possible "upgrade". If you place the blower on a tee like you suggested, in the seat box and exhause it out the back, you'd get forward propulsion....
Jim,
I'd like to invite you to join us at the SEMIWW (South East Michigan Wood Workers). We meet every third Thursday of the month in Ypsilanti. While not right around the corner, still not...
I personally don't buy bargin router bits... or any other tools for that matter. I did one time and didn't like how they perfromed. So now they sit on a shelf and I only pull them out when I need I'm...
Steve,
When I purchased my DJ20 I selected the mobile base. I seem to recall the base showed up in ~6 weeks. The rebate check shortly there after.
Robby,
Very unique indeed. Its not my taste, but then again, its not mine. Beautiful work. Your customer should be very pleased.
Steve,
I knew there was something I liked about you. Love the U.P.... escpecially during October and November.
Jim,
I might.. and I stress might be heading up to Harrisville in a...
Looks like I am too late. Tried to get in on the last years model deal but they are sold out. Still looking for suggestions. Has any one seen a review comparing the various turbine setup? Are the...
Typically most cabinet manufacturers will use the same interior for all their cabinets, irregardless of the exterior wood type. I think mine are a light maple type interior. Personally I like the...
I have narrowed the choices down to a turbine type spraying system. I currently have a relatively small ( 2-hp/8-gal) compressor which seems to work fairly well for what I use it for.. With that...
Not sure if I should post this here or in the finishing forum, so I did both.
I've been looking into an HVLP sprayer. I will primarily be using it for smaller projects using everything from...
I've been looking into an HVLP sprayer. I will primarily be using it for smaller projects using everything from laquer, polys and some paints (waterbourne ceramic based paint). Right now I am leaning...
I've looked through quite a few books. Most have good general information. Some are rather poor. But either way, I have not found a decent book yet that talks to actual dimensions. Basically the...
I'm getting ready to start building some kitchen cabinets. I am looking for a good source that has good details with cabinet dimensions. Are there also any good places to find kitchen cabinets plans?...
I'm getting ready to start building some kitchen cabinets. I am looking for a good source that has good details with cabinet dimensions. Are there also any good places to find kitchen cabinets plans?...
Richard, I believe you are correct.... I was told that the 4th ground wire was not needed because the neutral is grounded at the panel.
I also have a Jet cabinet saw. The saw will not have a plug. Probably best to have agrounded 220v plug. I installed a 3 bladed plug where all the blades are angles and one has a locking feature to...
Dan,
If it is truly in a crate I would wait until you get home. But like the others said, it probably won't be much more than a pallet and a couple of uprights. Either way, it won't hurt to...
I would glue and use tung oil. Easy to repair. Where did you get those rollers you are using for the outfeed for your planer? I've been looking for somethign along those lines. Nice looking bench....
I concur with Peter and Bill. One thing that might help is to use stop blocks on your router fence and boar being fluted. Set the blocks on the fence so the board will pass under the blocks. On the...
You got me... and I thought I finally hit pay dirt.
While I don't post on this site very often.... I'm always up for a good road trip. All I need is directions. Hope to be able to make it.
Very nice. Glad to see the client wised up.