Search:

Type: Posts; User: Steve Jenkins; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    23
    Views
    801

    It worked well. I only got a handful of in person...

    It worked well. I only got a handful of in person meetings but some of them ended in commissions. I also joined ASID (American Society Of Interior Designers) as an industry partner. That gave me...
  2. Replies
    23
    Views
    801

    When I started my business I knew that I didn’t...

    When I started my business I knew that I didn’t want to deal directly with the homeowner and all the time spent determining exactly what they want. At the time printed yellow pages were still...
  3. Replies
    32
    Views
    1,386

    Are you pressing down really hard as you push the...

    Are you pressing down really hard as you push the board through? Try dropping the blade below the table with the saw off and push the board through as if you were ripping it. It may be that your...
  4. Replies
    53
    Views
    2,127

    1949 Oliver 16” jointer

    1949 Oliver 16” jointer
  5. Replies
    6
    Views
    1,511

    Thanks for the compliment Valspar flat sheen...

    Thanks for the compliment
    Valspar flat sheen conversion varnish
  6. Replies
    17
    Views
    1,006

    Is it possible to loosen the riser block and...

    Is it possible to loosen the riser block and twist the top of the saw slightly. It won’t take much to correct the tracking
  7. Replies
    2
    Views
    314

    Haven’t done online with them but have had a...

    Haven’t done online with them but have had a commercial account with them for years.
  8. Replies
    23
    Views
    1,021

    I have a profile similar to that that I use. I...

    I have a profile similar to that that I use. I had knives made for an insert cutter head so I get the full profile in cope and stick.
  9. Replies
    20
    Views
    657

    You might look into Dispozablade. It’s a set that...

    You might look into Dispozablade. It’s a set that includes a self setting backer that their knives snap onto. The knives are double edged so it’s a simple matter of loosening the gib screws, pop the...
  10. 300 dollars for the hardware really doesn’t sound...

    300 dollars for the hardware really doesn’t sound bad to me. Like Jim said if they want it they should pay up.
  11. Replies
    29
    Views
    1,478

    I’d check with the Wood Component Manufacturers...

    I’d check with the Wood Component Manufacturers Association.
  12. Replies
    26
    Views
    1,120

    I have 8’ table to the left and 6’ skinney table...

    I have 8’ table to the left and 6’ skinney table to the right. Both tables are a couple feet off the wall and I use that space for vertical lumber storage
  13. Replies
    42
    Views
    1,398

    I would make a new top. Veneer on mdf then...

    I would make a new top. Veneer on mdf then edgeband with oak. To flush the solid I use a hand held belt sander but I’ve been doing that for a lot of years.
  14. Did you send this to MicroFence? I’m sure Richard...

    Did you send this to MicroFence? I’m sure Richard would like to see it.
  15. Replies
    24
    Views
    1,123

    I try to avoid straight router bits whenever...

    I try to avoid straight router bits whenever possible. I use either spiral or shear bits. Much less tear out.
  16. Replies
    145
    Views
    18,418

    At the end of his physical the doc asks if there...

    At the end of his physical the doc asks if there is anything else. Man says his wife is really hard of hearing but he doesn’t know how to tell her. Doc says when you get home say something to her as...
  17. Replies
    4
    Views
    365

    If you have a good biscuit joiner number “0”...

    If you have a good biscuit joiner number “0” biscuits will work
  18. I put a drip leg and moisture trap right after it

    I put a drip leg and moisture trap right after it
  19. I had a moisture problem years ago and purchased...

    I had a moisture problem years ago and purchased an after cooler from Grainger. It looks like a car radiator with a fan blowing through it. Works like a champ.
  20. Sounds like the edges may not have been square....

    Sounds like the edges may not have been square. I’d rip the joint apart the rejoint the edges and reglue. When you clamp alternate clamps above and below the panel checking for flat as you go....
  21. How about using the 15” slides and set them back...

    How about using the 15” slides and set them back from the drawer front. Attach a spacer to the drawer bottom to fill the gap between the front of the drawer and the slide. I’ve done this with Blum...
  22. Replies
    3
    Views
    363

    Chest piano convert to desk

    A friend of mine wants me to make the conversion. Has any one done this? I have the keyboard,soundboard, and harp out but looking for advice on cutting the piece above the keyboard and removing all...
  23. Replies
    7
    Views
    748

    I scoured the Freud website and they have a...

    I scoured the Freud website and they have a number of blades with lsb as part of their stock number but no explanation. They all have the laser cut expansion slots so I’d go with Richards explanation.
  24. Replies
    7
    Views
    748

    At least one of Freud’s lsb blades is Triple...

    At least one of Freud’s lsb blades is Triple chip positive rake
  25. Replies
    17
    Views
    1,021

    Make your offer. Either you will be surprised or...

    Make your offer. Either you will be surprised or he’ll say no.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4