Search:

Also, to Derek's question about coplanar and split top..

I followed Marc's (the wood whisperer) approach for setting up rails to carry a router sled for final flattening. Basically, two...

I just finished building my version of this bench, pretty closely following Benchcrafted's plans but using mostly power tools (and some hand tools). I left the center partition sitting just below...

Some seem to be suggesting that exhausting outside won't be a big impact to interior temp/humidity control... I have a really hard time believing that based on unscientific evidence around my own...

When I had a smaller DC (the usual HF model) and 4" duct, I vented outside with good results. I collected chips via Thien top hat setup, and outside the building I had the exhaust routed such that...

I know this isn't a "should I build or buy" thread, but I'll mention one thing... before I built my bench recently, I *thought* I was proficient at preparing lumber and performing glue ups... Boy...

Thankful to hear it was not worse!

I recently had my teenagers (with appropriate instruction, safety protocols etc.) do a mini project for me to use up a bunch of scrap plywood... they traced...

Before you buy.. since you have a new table saw already... lookup "table saw edge jointing" and watch a couple of videos. I think you may decide to save the $500 and try these methods for a few...

+1

I first had a benchtop delta... very difficult to work boards over a couple feet. I made it work, but it was not very enjoyable in my opinion.

Then I had a 6" Ridgid that was maybe 4...

Nice, thanks Ron! The consultancy I work for is located by Love Park (16th/Arch) so as covid lifts, I'll be in the city more often and will definitely look to check those out and connect with you...

We have a professional cornhole court setup at our place (yeah, I play a lot of beanbag toss! ha ha) and I built a mini-shed to house a normal ol' Roku TV. It's been out for a couple years now all...

lol, I damn near cut the red wire I think!!! :-)

I find necessity allows me to learn more easily. As the story above notes, my recent project had a few steps that were painfully ugly in terms of...

I agree - I've always been of the mindset that learning woodworking while also creating something useful or beautiful is a satisfying way to learn. Not that I haven't done a lot of practice...

Thanks again guys!! Lots of great info



Mark - agree with everything you wrote.. just a note, that I do a lot of woodworking already and am deep into the hobby for a bunch of years already......

:-) There are multiple tools in my shop that mock me from time to time, so my skin is getting pretty thick.

I had attended Jeffry Lohr's woodworking course years ago when I first started this...

Awesome, thanks guys!! I'll get busy watching and trying! :-)

Hi!
This is my first post in this section of the forum, and I'm sure in the archives this answer is lurking.. but if you can give me a head start I would greatly appreciate it.

I have been, and...

Ugh, I'm embarrassed to share my cobbled together prototype, but I shall do so for the greater good. :-)

Basically, I took 6" PVC to within a few feet of the bandsaw, and through a shop-made...

ESPECIALLY when it costs $0!! In this case, I just had to think differently, but the move didn't cost a thing. That's nice ROI!!!

Well, I got this step of the process done yesterday.

First, I took some grief from some SMC folks for my guesstimated selling price for my old drill press (but it sold for damn near that price in...

+1 on Jim’s comments. My HVAC professional explained that the technology has improved over the years but that the original “won’t work in the north” stigma remains

I'd be interested in any info on your assembly table... what you're mentioning is what I'm planning and I'd like to skip landmines if possible :)

Thanks guys!

Old drill press seems to be moving easily at that price, and I'll pickup something that better suits my needs

Edit.. SOLD last night at $250, so I guess I wasn't too far off with...

Wow, yeah that's nice, and also probably overkill for my specific usage. :-)


Last night and this morning, I have read a bunch about many DP's and have started to zoom in more on the Rikon...

Thanks guys! I posted it for sale locally and will monitor progress.

--

Now, onto the next part... For my uses (jig making, general home use, selected tasks for furniture making, and maybe a...

What number do you think would be fair? (and... do you think I should sell, buy something new... if new, what?)