Search:

Type: Posts; User: George Makra; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    370

    Try Jeffries Fine Lumber 8807 Valgo Road...

    Try Jeffries Fine Lumber 8807 Valgo Road Knoxville TN 37920 865 573 5876
  2. Replies
    4
    Views
    419

    Try a 4 inch no hub connector. Its in the...

    Try a 4 inch no hub connector.
    Its in the plumbing section and looks like a large hose clamp with a rubber sleeve inside.
    It will allow you to tighten on to different diameters with in reason.
  3. Replies
    81
    Views
    6,617

    The mind is the greatest tool you can ask for.

    The mind is the greatest tool you can ask for.
  4. Replies
    24
    Views
    970

    A picture of what you have would help. But I...

    A picture of what you have would help.
    But I will take a stab a what is going on and this is the manual for it....
  5. Replies
    6
    Views
    545

    Tim I used to build and maintain clean rooms....

    Tim I used to build and maintain clean rooms.
    Your request will never happen in the real world for a wood shop.
    Thats like saying you want to be dropped out of a helicopter over a lake and not...
  6. Replies
    20
    Views
    1,317

    Times 2 on the Carter Fence

    Times 2 on the Carter Fence
  7. Look up vee nailer I have had both floor version...

    Look up vee nailer I have had both floor version and hand held version.
    The floor version is a PIA, the hand held is very quick cost about 150 on flea bay.
  8. Replies
    6
    Views
    528

    You will either have to install a condensate pump...

    You will either have to install a condensate pump (most manufactures will sell one that fits inside their unit.
    Or if you have the capability a gravity drain line with a 1/4 inch per foot fall.
  9. Well if you look at root cause you will see what...

    Well if you look at root cause you will see what the problem is.
    Sorry couldn't help my self.
  10. From the manual MOTORYour Delta Radial Arm Saw...

    From the manual
    MOTORYour Delta Radial Arm Saw is equipped with a dual voltage motor capable of 120 volt, single phase operation or240 volt, single phase operation. The motor on your sawis shipped...
  11. Replies
    36
    Views
    2,612

    Shellix I own one of their heads on a Delta 6 X...

    Shellix I own one of their heads on a Delta 6 X 13 thickness planner and I love it.
    I have run thousands of feet of oak through that machine with out so much as a tear out.
    Might you have to dress...
  12. Replies
    12
    Views
    642

    Yeah an other option is to look up burnishing...

    Yeah an other option is to look up burnishing machine on Amazon and get your self one with a nylon brush for about 250.
    Its a whole lot cheaper and about 2/3 as fast.
  13. Replies
    14
    Views
    1,077

    Add a couple drops of penetrating oil let soak...

    Add a couple drops of penetrating oil let soak then heat the collet with a heat gun and apply gentle force and it should come out.
  14. Replies
    12
    Views
    642

    Sanding will level the board but leave dirt in...

    Sanding will level the board but leave dirt in the grain.
    At the lumber yard I get a lot of my wood from have an industrial wood brush machine and they have both nylon and wire brushes.
    Nylon will...
  15. Replies
    8
    Views
    637

    If the OP was curious to see if there is a "C...

    If the OP was curious to see if there is a "C Frame motor) in a smaller HP I would think the answer is yes but you need to to contact a motor shop that deals in IEC European motors.
    Converting the...
  16. Replies
    27
    Views
    2,078

    You know I really have to take amp readings but...

    You know I really have to take amp readings but as far as I can tell the carbide head taking more amps to spin sure sounds like another internet myth.
    Here is what I do know I have a older Delta...
  17. Replies
    14
    Views
    948

    Its call break away torque. It typically takes 7...

    Its call break away torque.
    It typically takes 7 times the FULL LOAD AMPS to go from a dead stop to rated RPM.
    If you had a recording amp meter you wold see it.
    But in the end it is normal...
  18. Replies
    59
    Views
    6,557

    Forest blades use to have a real nice write up on...

    Forest blades use to have a real nice write up on setting up your saw. You can call them and ask if they could email it to you.

    It covers everything and IRRC it about 4 pages long.
  19. Replies
    59
    Views
    6,557

    Its customary to have the back side (post cut)be...

    Its customary to have the back side (post cut)be a few thousand wider to allow the wood to expand from the cutting process.
  20. Replies
    7
    Views
    944

    Well 80/20 can be quite a rabbit hole I know...

    Well 80/20 can be quite a rabbit hole I know cause I went down it back when Jimmy Carter was in charge.
    Things are different now
    I also looked at after market fences and they were all junk..
    So...
  21. Replies
    11
    Views
    1,002

    Set your fence at the 1 or 2 or whatever you want...

    Set your fence at the 1 or 2 or whatever you want cut the piece of wood and measure the cut piece.
    Then adjust your measuring window to the recently cut item.

    As an example say you want to cut 1...
  22. Replies
    7
    Views
    768

    What Adrew said is correct plus it really likes...

    What Adrew said is correct plus it really likes to crack.
  23. Replies
    30
    Views
    2,054

    You could also use cross dowels.

    You could also use cross dowels.
  24. Align it like you did then to get the belt...

    Align it like you did then to get the belt straight and then get a couple blank inserts and make zero clearance inserts for your blades.
  25. Replies
    11
    Views
    1,161

    Your filters are fine! And here is why, years...

    Your filters are fine!
    And here is why, years ago before MERV ratings they had % numbers such as 40% or 80%.
    The test conducted in a test chamber and 1 pound of dust was introduced into the air...
Results 1 to 25 of 61
Page 1 of 3 1 2 3