Search:

Type: Posts; User: Tony Joyce; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    505

    Is this what you are looking for? I just saw this...

    Is this what you are looking for? I just saw this and vaguely remembered reading this post.

    411665
    https://www.micromark.com/Micro-Make-MicroLux-Contour-Sander
  2. 407945Light Color Chart

    407945Light Color Chart
  3. Same here. Currently have at least six going....

    Same here. Currently have at least six going. Finishing doors for one job(cabinets previously done), Building miter frame doors for another client(plus finishing them), two furniture projects and one...
  4. Replies
    146
    Views
    18,738

    I have to agree 100%. Good assessment.

    I have to agree 100%. Good assessment.
  5. Replies
    14
    Views
    1,012

    Almost the same here except I consider it...

    Almost the same here except I consider it necessary, because cell service is so poor(rural area). I have Spectrum with two lines. They have nomorobo and call blocking, but with a forty number limit....
  6. Replies
    4
    Views
    504

    Reach out to ...

    Reach out to
    jack forsberg
    a member on this site most likely Jack can answer your questions. He is a Wadkin guru.

    Tony
  7. Replies
    12
    Views
    1,593

    Dr. Jim Moon's take on Studley...

    Dr. Jim Moon's take on Studley https://www.instagram.com/p/BUTAS_MlHgK/

    Note: This is a reproduction, Dr Moon does amazing work.

    Found another article about Dr Moon....
  8. Replies
    17
    Views
    1,404

    I have a full set of the Ashley Iles MKll...

    I have a full set of the Ashley Iles MKll chisels. I have owned these for about 8 years. I sold a set of the now discontinued larger handled ones. These are not paring or mortise chisels. (By the way...
  9. I guess it comes as no great surprise that F&W...

    I guess it comes as no great surprise that F&W has filed for bankruptcy. For now no more "Popular Woodworking"
  10. Replies
    21
    Views
    2,646

    I went with a box, but I'm reconsidering that...

    I went with a box, but I'm reconsidering that now. I may go with a drawer when I build my tool chest.
    405009405010
  11. Replies
    19
    Views
    2,155

    402898 This is mounted on the wall behind my...

    402898
    This is mounted on the wall behind my lathe.
  12. Replies
    11
    Views
    905

    Based on my rudimentary understanding of what you...

    Based on my rudimentary understanding of what you are doing my suggestion is the Incra Tools Positioner.
    https://www.incra.com/table_saw_fences-tsls_fences.html
    While not cheap it is accurate, fast...
  13. Thread: Leach Tools

    by Tony Joyce
    Replies
    22
    Views
    2,089

    I've purchased a few items from Patrick and was...

    I've purchased a few items from Patrick and was pleased with my purchase's. I've met him in person, he's brutally honest and knows what he's talking about. He can be trusted, but has no time for BS....
  14. Replies
    5
    Views
    751

    Sherwin Williams PreCat will only be available in...

    Sherwin Williams PreCat will only be available in gallons.
  15. Replies
    14
    Views
    1,089

    That along with good flat lumber to begin with....

    That along with good flat lumber to begin with. My opinion/experience is if the lumber is dry and flat in the rough it will likely stay flat in the finished project.
  16. Replies
    138
    Views
    10,255

    I wear my Rolex DateJust daily and have everyday...

    I wear my Rolex DateJust daily and have everyday since it replaced the Baume & Mercier Riviera I wore everyday prior to that. I prefer the Baume for work wear, because it is thinner. I've discovered...
  17. Replies
    14
    Views
    1,089

    RE: Finishing table tops on both sides?

    I've always seen on internet replies to finish both sides of table tops. I've often wondered if it was necessary. This post by Bob Flexner confirms my suspicions and experience. I'm sure this will...
  18. Mike, Thanks for your reply. It's all good. ...

    Mike,
    Thanks for your reply. It's all good.

    The reason I put CNC router replies is I wanted to work within the confines of what I had, as opposed to suggestions to buy more equipment.

    Thanks,...
  19. Helpful info Thanks. I have bought several bits...

    Helpful info Thanks. I have bought several bits on eBay, but never engraving bits. I definitely give that a try.

    I'm pretty up on converting bitmaps to vectors, no problems there. No coolant,...
  20. Mister for Vbit engraving?

    I hadn't considered the need for lubricant. I guess you would need a mister like for cutting Aluminum? Which is something I was considering adding anyway.

    Thanks, Tony
  21. I should have been a little more specific. What...

    I should have been a little more specific. What I'm mainly thinking about at present doing brass with some lettering, maybe some scroll line art. Probably 3/8" - 1/2" in height on the lettering....
  22. Diamond Drag vs Engraving Cutters on CNC Router??

    Please keep it to CNC router based information, Thanks. I'm just trying to find out capabilities for use with what I have. I'm not looking for more equipment
    Pros?
    Cons?
    Opinions welcome
    First...
  23. Replies
    11
    Views
    1,175

    I've followed along as newer versions of Aspire...

    I've followed along as newer versions of Aspire were released. I'm especially looking forward to the threading capabilities. And better drawing tools. Still it's going to be almost like a new...
  24. Replies
    11
    Views
    1,175

    An explanation which should have been obvious,...

    An explanation which should have been obvious, but only made sense to me with your answer. I only use wish there was a "WinCNC for Dummies" book.

    Thanks again for your time, Tony
  25. Replies
    11
    Views
    1,175

    Jim, A little background, I ran this machine(4X8...

    Jim,
    A little background, I ran this machine(4X8 with ATC) for about five years when it was new(around 2009). The machine was sold about two months ago and is now in my shop.

    I understand the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4