I have a MM3 and just sprayed the HSF5000 for the first time a couple weeks ago. I have the 3m PPS system and used the 1.8 mm tip. It sprayed really well. No thinning required.
Brian
Type: Posts; User: Brian Cosgrove; Keyword(s):
I have a MM3 and just sprayed the HSF5000 for the first time a couple weeks ago. I have the 3m PPS system and used the 1.8 mm tip. It sprayed really well. No thinning required.
Brian
I second Supplyhouse. Ironically, I just spent $500 there a few minutes ago on pex-a and expander fittings. I have the Milwaukee expansion tool and it works amazing. I almost feel like I’m cheating...
Very ironic topic. I just scheduled an appointment yesterday with a hand surgeon, which I believe will end up being a diagnosis of Dupuytren's. My issue is with the right ring finger and is still...
I see that most people use the 1" 1.3 tpi blade (Woodmaster CT), however, it is also available in 2 tpi. Does anyone have experience with this blade? Would this give a finer finish, albeit while...
+1 for the Rolair JC10. I use it for the pneumatic clamps on my sliding table saw and the thing is awesome. super quiet compared to any other job site type compressor. I have also used it for my brad...
I live in West Seneca, a suburb of Buffalo, which is in the heart of the storm. We got 6ft here at my house. I'm 38 years old and have lived here my entire life and this is the most significant snow...
Thank you Kent. I hadn't noticed it was full. Bucket emptied
Thanks for all of the input so far. Another question for discussion........I have plenty of power to run a phase converter for a larger machine and everything I read points to 3 phase being...
I will admit that I know nothing about stroke sanders and do not want to buy a drum sander just so I can upgrade next year. I did that with my slider and jointer/planer by buying cheap before...
Rick, my main sanding is end grain butcher block of various sizes, from cutting boards to island tops. Maple, cherry, walnut.
Brian
Another brand that comes to mind if Safety Speed Cut, which are priced reasonably. Anybody have experience with these?
Mike, Thanks for the reply. I did consider the Speedsander and like it a lot, however, I did notice the maximum sanding thickness is 4" vs. 6 1/4" for the mentioned SCMI machines. I think I would...
Hi. I am in the market for a wide belt sander. I am a serious hobbiest and will be the only one using it, likely a few hours a week maximum. Based on my anticipated need, I have decided that I want a...
I am also on the hunt for a similar square. I was looking at this one in the 18 x 8 size after it was mentioned by someone on the Felder Owner's Group.
http://www.brassandtool.com/Squares.html...
Thanks Keith, Count me in
Brian
count me in.
Thank you
New York State law is that when turning left from a single left turn onto a multi lane road, you turn into the lane closest to the center of roadway (in this case left lane)
I would use an angle grinder with a 6" cut off wheel/disc. Mark the line with a sharpie and cut it. It is actually pretty easy to maintain good control for a nice quality cut.
Sorry to hear about your loss. Several years ago, I lost a great dog to cancer at age 7. I know how you feel. I was torn up for a long time. It will get better, though. You will never forget her.
Greg, was the A3-31 you got the one that was on craigslist in Philly for awhile? I also have an A3-31 and love it. I also have a K3 with the 78" slider. I like it alot, however, may be selling it...
Congratulations Chris. I got the same saw back in February. I love it so far. Seeing the pallet wrapped up like that brings back great memories from the day I got mine.
Brian
There is a minimally used Hammer K3 in the classified section for 4,000 or best offer, with several blades. I have the same saw and really like it. The dado king and woodworker II blade are worth...
20 amp breaker with 12 gauge wire should be fine
I have Hammer A3-31. You only need 12/2 wire, 20 amp circuit with nema 6-20p outlet. 20 amp breaker is fine, per Felder USA.
Brian
This question is for anyone who has a Quality Grinding router table or extension with miter slot. If the top is only 3/8" thick, I would think the depth of the miter slot would be deep enough to...