Search:

Type: Posts; User: Adel Heiba; Keyword(s):

Search: Search took 0.00 seconds.

  1. Max Bit Size Hammer A3-31 Slot Mortiser

    I would like to create slot mortises of 3/4 thickness with a Hammer A3-31 slot mortiser. The closest bit Birds Mouth Bit size that I can find online is 20 mm. Is the 3 hp motor on the mortiser...
  2. Replies
    20
    Views
    2,339

    Thank you for all the suggestions! The ‘Miter...

    Thank you for all the suggestions!

    The ‘Miter Jack’ is a neat idea; but, the complexity of its construction would make the original problem a trivial exercise. However something like the Miter...
  3. Replies
    20
    Views
    2,339

    Accurate Bandsaw Cross cut?

    Hi

    I have a Felder 400 FB bandsaw and I need to perform accurate crosscuts on thick stock (about 2.5”) and about 5” wide.

    Usually I do crosscuts by hand and correct with a shooting board; but...
  4. Replies
    9
    Views
    1,450

    Hammer A3 31 Jointer Bed Question

    I have recently come to notice a slight concavity on the infeed table of my A3-31 jointer. The concavity is in the direction that is perpendicular to the fence.

    The concavity does not seem to...
  5. Replies
    6
    Views
    1,253

    Hi Jim Thank you for your response. Adel...

    Hi Jim

    Thank you for your response.

    Adel Heiba
  6. Replies
    6
    Views
    1,253

    I meant I have been using 8 mm not 10 mm —...

    I meant I have been using 8 mm not 10 mm — correction
  7. Replies
    6
    Views
    1,253

    Thanks — Mick and John! On my next table of...

    Thanks — Mick and John!

    On my next table of 7/8” aprons, I will try to up my float tenon size to 10 mm from 8 mm. I have been using the former.

    It is difficult to translate the old rules for...
  8. Replies
    6
    Views
    1,253

    Question about Loose Tenon Size

    What are the rules for sizing loose tenons? I am interested in constructing a table by connecting a 7/8” apron to a 2”” table leg with loose tenons. What should the thickness off the tenon be? How...
  9. Replies
    11
    Views
    1,796

    Winding Sticks for Table Legs

    Just curious— I have constructed a table and I have no reference surface in the home to consider as dead flat for the size of the table. I want to make sure that it sits flat on the floor. Are...
  10. Replies
    6
    Views
    2,063

    Hi Mark From your response I am not alone. In...

    Hi Mark

    From your response I am not alone. In the past I have used shooting boards following a cut with the Ulmia and kind of forgotten about the issue. The issue came up again with cutting table...
  11. Replies
    6
    Views
    2,063

    Generally, different blades cause different...

    Generally, different blades cause different directions in the vertically cut
  12. Replies
    6
    Views
    2,063

    ULMIA 354 Question

    Several years ago, I purchased a new Ulmia 354 mitre saw. I have had mixed results with accuracy— horizontally the accuracy is excellent. Vertically I get mixed results — some times the cut veers to...
  13. Replies
    47
    Views
    20,028

    Hi Matthew, The snipe is while planing. I...

    Hi Matthew,

    The snipe is while planing.

    I have not seen instructions in the manual — just curious if there are formal instructions online.

    The other concern that I have is the operation of...
  14. Replies
    47
    Views
    20,028

    Hi Tim, i have had the Hammer A3 31 with...

    Hi Tim,

    i have had the Hammer A3 31 with helical cutter head for about a decade. Recently, I have noticed some snipe. Is there any advice or video on how this is to be eliminated?

    Also, I am...
  15. Replies
    5
    Views
    938

    Metric Router Bits

    Question: where can metric router/mortiser bits be purchased? Domestic suppliers seem to be limited to English units.
  16. Slot-Mortising-Hammer-A3-31 - mobility kit for mortiser?

    Hi,

    Has anyone constructed (or bought) a mobility kit for the slot mortiser attachment to the Hammer A3 31 jointer planer.

    If so please send a picture and any additional information about the...
  17. Replies
    3
    Views
    679

    Kevin, Thank you — I think what you suggest...

    Kevin,

    Thank you — I think what you suggest will work after a few trys!

    Adel
  18. Replies
    3
    Views
    679

    Slot Mortising Hammer A3 31

    I have a problem routing mortises with Slot mortiser. Because of my technique or lack thereof the mortises in the leg tend to be slightly wider than those in aprons. This makes for a loose fit in the...
Results 1 to 18 of 18