Just wondering if this sprayer sprays clear polyurethane well? Everything I’ve seen on this sprayer involves colors, where I mainly use clear poly.
Type: Posts; User: Derek Arita; Keyword(s):
Just wondering if this sprayer sprays clear polyurethane well? Everything I’ve seen on this sprayer involves colors, where I mainly use clear poly.
Thanks Michael. Seems pretty straightforward for a computer dummy like me.
Just got a set of these and thought I’d post here. Yes, they’re expensive, but I was at the end of my rope dealing with having to apply “tons” of pressure on my drill press to get my old bits to...
Also, I'm looking for easy to use, as I'm a real dummy with this stuff.
I've been trying to use Imgur's new site, but can't make heads or tales of how to load and resize my photos for forum use. Please give me suggesting on the easiest apps to use for this?
Al, this is precisely why I added the short wooden runners to the ends of the bars. With those added bars, I can accurately cut 24”+ wide sheets and it works perfectly without being effected by...
Dan, please finish with your explanation. It seems you were cut off. Also, I’d love to read that analysis you referred to if you can provide a link or something.
Dan, explain that to me, because it doesn’t make intuitive sense to me. Each bar has one side in full contact with one side of its slot while the sprung side is in contact with the other side of the...
Dan, I find that hard to believe and at this point, couldn’t disagree with you more. I have an excellent miter gage with a long, solid fence. I can only use it for ruff cuts. Convince me.
Dan, I think you’re wrong in general, however I’m sure there are areas of extreme humidity swings that might apply. Having used one and two bars, I am positive that two is more dependable and gives...
Just wanted to post in case anyone was interested. I was setting up to make a couple of large sleds for my SS Compact saw, so I purchased both the Woodpecker and the Incra Special Edition Miter...
What I used to do with wood bars was to put the bars in the slots, slightly raised, apply some glue to them, then place the sled on top of them, aligned with the front of the table. That way I knew...
Ok…so I just purchased a pair of both the Incra and Woodpecker miter bars. The one question I have is, how do you attach the miter bar from the top? For some reason, I can’t imagine how that’s done.
Boy, that sure does seem to fit the bill, although as usual with WP, it’s pricey. Thanks.
I’m looking for help finding good miter bars for a sled. They have to be at least 24” and screw in from the top. I’ve seen some with only 3 miter slot adjusters, however I’d like to have more. Any...
Yes. For the ZCI, they’ve supplied extra inserts. As for the Cube, I could purchase more, print them or make some out of 4x4.
Thanks, good advice. I’ll do that.
As the title says I installed the Cube along with the ZCI and I like them both. Of course, the ZCI keeps the thin off cuts from falling into the cavern of no return but the Cube gets rid of those...
Hope this helps…
https://i.imgur.com/lUqPK9d.jpg
Tom, I slid 2 shims on either side of the slot, between contact surfaces, above the upper screw and then 2 more below the lower screw. They are short shims and must be bent to fit in those narrow...
Ok Tom, you asked for it. There are two nuts holding on the cover of the ways. Removing those exposes where the table meets the ways and it’s where the manual says you should lubricate for smooth...
Actually, it’s a 12”. My MM was a 12” as well, however it has Teresa knives. I find the Griz is quieter, but at a higher pitch. I’m sure the helical head helps with noise reduction. I don’t find it...
Not much posted on this machine anywhere, so I thought I'd post in case anyone is interested. The lead is, I like it, but it's not without it's issues. I've had several jointers and few planers,...
Ya. I know you’re right. That way I know the cutter edge is even with the table, or maybe a a smidge higher?
Can I rest then end of my dial indicator on the body of the head or does it have to be on the TDC of a blade edge?
https://i.imgur.com/cBMBQ4R.jpg